DMX2REN design
 
Notifications
Clear all

DMX2REN design

56 Posts
14 Users
0 Reactions
23.3 K Views
Macrosill
Posts: 9739
Topic starter
(@macrosill)
Member
Joined: 19 years ago

The mounting holes are to fit a particular enclosure.

The 5v traces are .02 inch on 2oz copper. They need to carry between 500 and 1000ma. The .02 trace should be capable of carrying 2.1 amps with a 10c rise in temp.

Yes, vertical rj45s all around.


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:...I'm debating whether the ground on the RJ45 connectors should be tied to ground on the DMX2REN board, or whether it should just rely on the ground connections on the Ren64-XB. Perhaps it would be best to make provision on the DMX2REN board for a jumper (or a 0-ohm resistor) between the two grounds, so that you have something that is easy to play around with.

A DMX receiving device's shield/common should be floated and not tied to common. A DMX transmitter grounds (AC ground) the shield for the entire system, which prevents ground loops.


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

Brian,

looks like you are makign this board so it cant be easily made at home, fair enough, but a couple of simple changes would make it possible,

running the ground trace though the middle of the DMX out RJ45 makes it pretty hard to make at home. i would run the ground vertical parrallel with R2 and then add a second jumper to get it to the ground trace between the next two rj45's.

also i would assume 1/2oz copper or at best 1oz. assuming 2oz makes it a hard board to make. and being that the extra copper costs money i think you will find slightly wider 1/2 oz or 1oz traces would be easier.

As for the fuse it looks like you have added a fuse like in the classic SSROZ board. the only issue with those is the height. but being it is beside the transformer then it shouldnt be an issue. you might want to talkt o WJOHn about the hole spacing he uses due to the different fuses available in the states and here in aus. While you looking at that side i would add some more width to the AC side as well. you never know who might want to run 240v though this board. oh and keep an eye on the track spacing. should be fine but now is the time to think about it.

anyway thats something to think about


Reply
Posts: 899
 lbro
(@lbro)
Noble Member
Joined: 19 years ago

Okay, here is a question, can I use this board with 595's? Trying to look at ways to still use them.


Reply
Macrosill
Posts: 9739
Topic starter
(@macrosill)
Member
Joined: 19 years ago
scorpia wrote:Brian,

looks like you are makign this board so it cant be easily made at home, fair enough, but a couple of simple changes would make it possible,

I am making this board for me to etch at home.

scorpia wrote:running the ground trace though the middle of the DMX out RJ45 makes it pretty hard to make at home. i would run the ground vertical parrallel with R2 and then add a second jumper to get it to the ground trace between the next two rj45's.

I have done it b4

scorpia wrote:also i would assume 1/2oz copper or at best 1oz. assuming 2oz makes it a hard board to make. and being that the extra copper costs money i think you will find slightly wider 1/2 oz or 1oz traces would be easier.

I only have stock of 2oz copper so that is what I use.

scorpia wrote:As for the fuse it looks like you have added a fuse like in the classic SSROZ board. the only issue with those is the height. but being it is beside the transformer then it shouldnt be an issue. you might want to talkt o WJOHn about the hole spacing he uses due to the different fuses available in the states and here in aus. While you looking at that side i would add some more width to the AC side as well. you never know who might want to run 240v though this board. oh and keep an eye on the track spacing. should be fine but now is the time to think about it.

anyway thats something to think about

I have about 50 of those fuse holders so I am using them. I will only be running 110v on this board.

Again, this is not a coop board, just a pcb I need as a solution for my current hardware and future direction. But those are all valid points if this was going to be made by others. I can incorporate all of those things into a new file if others will use it, provided my layout and BOM will work.


Reply
Page 4 / 12
Share: