dirknerkle's Ren64/...
 
Notifications
Clear all

dirknerkle's Ren64/Ren-W problem

17 Posts
5 Users
0 Reactions
7,118 Views
Capt'n Jack
Posts: 274
Topic starter
(@capt-n-jack)
Reputable Member
Joined: 18 years ago

I'm still trying but no luck yet.


Reply
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
Capt'n Jack wrote:I'm still trying but no luck yet.

Did you read the Wiki section for the Ren-W about reflashing the firmware? I believe it's in the "Configuring the XBee" section down near the bottom of the page. There's a point when you actually have to remove power to it and then quickly repower it to "boot" it and then the upgrade goes.


Reply
Capt'n Jack
Posts: 274
Topic starter
(@capt-n-jack)
Reputable Member
Joined: 18 years ago

It keeps losing communication before downgrade is complete.


Reply
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Yes, that happens unless it's been rebooted. Here's the section from the Wiki:

a) If the radio gives a "disconnect" kind of message on the bottom of the screen, do steps b-g below. If it does not, it will update the firmware directly, then go to step #8.
b) Leave the Explorer board plugged in but unplug the XBee from the Explorer board.
c) Click the WRITE button again, even though the radio is not plugged in. Wait a few moments, and a screen should appear that has a lot of words and options. Just do the next step quickly.
d) Plug the XBee radio back into the board. The screen should disappear, and you should get a note on the screen that the XBee is "initializing." After that, it will go to programming.
e) Another screen with text and options may appear. Unplug the radio again from the Explorer board, count to 1 and plug it back in.
f) It should then read the AT commands to display the XBee's settings page again.


Reply
XmasInGalt
Posts: 526
(@xmasingalt)
Honorable Member
Joined: 19 years ago
Capt'n Jack wrote:It keeps losing communication before downgrade is complete.

Capt'n Jack, I had the same problem with a board I built to program the Xbees. After reading all the online documentation I could find, I found a couple forums that talked about having the same problem during programming. The suggested solution was to connect pin 9 of the Xbee to ground. The Digi spec sheet refers to this pin as the Pin Sleep Control Line or Digital Input 8. I followed the suggestion of the forums I read and I haven't had any problems with programming any of my Xbees since then.


Reply
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
XmasInGalt wrote:Capt'n Jack, I had the same problem with a board I built to program the Xbees. After reading all the online documentation I could find, I found a couple forums that talked about having the same problem during programming. The suggested solution was to connect pin 9 of the Xbee to ground. The Digi spec sheet refers to this pin as the Pin Sleep Control Line or Digital Input 8. I followed the suggestion of the forums I read and I haven't had any problems with programming any of my Xbees since then.

FYI, Pin 1 is +3.3v. Pin 10 is GND.


Reply
Capt'n Jack
Posts: 274
Topic starter
(@capt-n-jack)
Reputable Member
Joined: 18 years ago

Just in case anyone else has this trouble, I've found you have to be VERY FAST plugging the XBee back in just as the text screen appears. Thanks to dirknerkle my XBees are now upgraded.


Reply
Page 2 / 2
Share: