Another Ren64 Appro...
 
Notifications
Clear all

Another Ren64 Approach

28 Posts
10 Users
0 Reactions
10.5 K Views
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

I'm on a slightly different tack as far as enclosures go. I'm considering the CG-1500 case, with the board mounted horizontally. For those who want higher density there is room for two of these boards using the 'new' mounting holes. This is based on the dimension file downloaded from the wiki. The two mounting in the attached diagram are 0.5" apart in the vertical direction and 6" apart horizontally, with the right hole 1.375" from the right side of the board.

I tried to find locations for the mounting holes that would have allowed it to be nicely mounted in the CG-1000 enclosure, but couldn't find a way with major surgery on the board. The board would fit horizontally in the CG-1000 with a small amount of room to spare, I think, but I couldn't find a way to conveniently position at least two mounting holes near opposite ends of the board.

Edit: and for either enclosure, I wanted at least one hole near the transformer, as it is fairly heavy and needs support imo.

renard64 4094 1

Reply
Don6699
Posts: 185
(@don6699)
Estimable Member
Joined: 13 years ago

I've used this item for years to mount back plane based cards but it only comes in 4" and 2.5", RIB® Mounting Track MT4-48, 4"W x 48"L.
http://www.globalindustrial.com/p/electrical/relays-sequencers/relay-accessories/mounting-track-mt4-48-4w-x-48l
So you would have to adjust the width of the pcb to 4"...
One more thing, the stand off should allow you to place some of the components on the backside of the pcb with at lease 1/2" clearance.


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago
Don6699 wrote:I've used this item for years to mount back plane based cards but it only comes in 4" and 2.5", RIB® Mounting Track MT4-48, 4"W x 48"L.
http://www.globalindustrial.com/p/electrical/relays-sequencers/relay-accessories/mounting-track-mt4-48-4w-x-48l
So you would have to adjust the width of the pcb to 4"...
One more thing, the stand off should allow you to place some of the components on the backside of the pcb with at lease 1/2" clearance.

I'll keep that in mind for future projects, but they seem a bit expensive for this one.


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

I think that I'm going to let this gestate for a while. I've some other projects that are begging for me to give them more time.

In the meanwhile, I've added a few more option jumpers to the board. One of them is to allow the user to select whether the transmit data comes from the PIC or from the incoming RS485 data. Another jumper can be used to select between normal operation, writing configuration data to the EEPROM, or going into a (light) test mode similar to the ctmal's tester. The third jumper can be used to remove the ground signal from the SSR's, so that power LEDs on the SSRs aren't consuming any power.


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

The project is still in gestation, but I did send off for this little PCB for testing the firmware against a Grinch board (the biggest difference is in the polarity of the clock signal, if I'm not mistaken). The board is 0.65" x 2.00", and has on it a footprint for a full-duplex RS485 controller and almost any PIC12F/PIC12HV/PIC12LF part along with the ICSP connector.

This little board is multi-purpose:

1) testing the logic for driving the '595/'4094/MBI5027 chips
2) small 3-channel servo controller
3) simple RS485 receiver/transmitter (omitting the PIC)
4) traffic generator for testing PX1
5) pixel controller ???

renard ifc

Reply
Page 3 / 6
Share: