Another Controller ...
 
Notifications
Clear all

Another Controller Design

370 Posts
27 Users
0 Reactions
128.2 K Views
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago
[#7044]

A lot of the ideas on this board are simply re-packaging previous designs, and this is another one of those. These are 1.5" x 2" home-etch SMT boards. One is a 16-channel controller using a PIC16F722, the other is a 4-channel SSR board using Z0107 triacs (good for about 1A per channel). These are intended to fit in a 1.5" tube (PVC or otherwise). It remains to be seen if 16 pairs of output wires (SPT1 or similar) will fit through a tube of that diameter...I'll have to use a larger diameter tube if it doesn't fit.

Just food for thought...

HPIM0722 mod

369 Replies
cbell
Posts: 462
(@cbell)
Honorable Member
Joined: 18 years ago

That's pretty neat Phil! That would solve a design issue I'm working around in trying to split my icicle lights into 50 light channels so that they can chase around the roof. Something like this would definitely keep the cord usage (and weight and bulk of the cords) to a minimum.

Now I just need to teach myself how to home etch and to solder SMT lol 😉

Good work Phil!


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

These boards are easy to solder using regular hand tools. The finest pitch parts on these boards are .050", which can be easily soldered with a fine-point soldering iron. This is probably not the recommended method, but it seems to work for me.


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

phil,

any chance you could send me the board layout as a pdf or something. its hard to trace your wireing off a fuzzy pic. 🙂

hopefully you have finalised the layout for this chip so i can get a pcb made up to suit.

Peter


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

For me, soldering surface mount with my soldering iron works fine.
The .050 pitch helps, but I'd also recommend ultra-fine solder.


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

Scorpia,

I could send you the layouts in .pdf format, although it is too early to make boards from them. I'm not done debugging the design yet, particularly the firmware.


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

it will take me a little time to update my design and get it ready production.

im assumig the design is based of the firmware i was testing for you after christmas.

Peter


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

The firmware is based on what you've seen. The charlie-plex code makes the ISR a bit longer, so I have to optimize things other places. It'll take a little while to get things working again.


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

Very cool, a surface mount Renard project. Same concept as we are used to, just different soldering techniques.


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

The firmware seems to be working now, so I'm going to make a more complete setup and do a more comprehensive test. There were a few bugs on the PCB designs. The controller board needed a larger input filter cap, and the triacs were backwards on the SSR board. Oh, well.

Just as an FIY, these boards are meant to be used in the same manner as the original Renard8 design. They have a fairly low power budget (non-PWM), so pins 7/8 of the RJ45 connector are used for both zero-crossing and power inputs. This input signal can be very nicely provided by the Ren-T board, which should be capable of driving some number of these 16-channel controllers. However, there is nothing that would preclude using PWM firmware if a more robust power supply is provided.


Reply
Page 1 / 37
Share: