Dancing Lights - GE...
 
Notifications
Clear all

Dancing Lights - GETTING STARTED....

61 Posts
14 Users
0 Reactions
20.9 K Views
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

Both of the above helpful responses. Thanks guys!


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

Well I took a crack at soldering the beginner kit I bought online and guess what - IT WORKED! It didn't seem too hard.

I do have a question from the experience though and I don't know if I addressed this before somewhere else but...

The kit came with lead-free solder. Will that be OK or should I use leaded solder when assembling the Ren 24 controller?


Reply
omzig
Posts: 1603
(@omzig)
Noble Member
Joined: 19 years ago

You can use the lead-free, but I wouldn't. Lead-free solder melts at a higher temperature so you have to apply more heat to the components. Unless you plan on exporting to Europe (doubtful :-)) you can use lead-based solder. IMO it is much easier to solder with lead. The most common lead-based solder is 60/40 (60% tin/40% lead). The best is 63/37 which costs a little more but it is the easiest to work with.


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

How dangerous is it to use lead solder around kids? I would be in the basement and not right on top of them, but just wondering how harmful this may be.


Reply
Macrosill
Posts: 9739
(@macrosill)
Member
Joined: 20 years ago

no harm unless they put it in their mouths or you do not wash your hands after handling it. The lead in the solder needs a much higher temp to vaporize than any soldering iron can produce.


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

Has anyone out there used the lead-free solder to construct one of their boards? If so, outside of the melting point, were there any other drawbacks?

The reason I ask it because with the kit I got, it had lead-free solder and it didn't seem too difficult to work with. I used a 25 watt iron and didn't seem to have any problems.


Reply
kmc123
Posts: 824
(@kmc123)
Prominent Member
Joined: 19 years ago

I've never used it, so I'm interested as well - Most of the things I've heard had to do with the melting temp, but it sounds like it's working for you...


Reply
WWNF911
Posts: 1722
(@wwnf911)
Noble Member
Joined: 19 years ago

Some experimenting is due. I've worked with some solder that works very well and others that are SH__!!! My local electronics store has some that is very small in diameter and works the best for me. (Not lead free) 🙂


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

I just want to be sure that I don't damage the board due to the higher melting point of the lead-free variety. With the kit I have, I used a 25 watt iron and .03 diameter solder and it seemed to work OK.

Like I've said, I'm a major newb, but it didn't seem to take overly long to solder the joints -> 3-4 seconds probably.

The way it seems though, based on the low number or replies regarding the lead-free stuff, most like sticking with the 60/40 flavor. Maybe I should just go that route.


Reply
WWNF911
Posts: 1722
(@wwnf911)
Noble Member
Joined: 19 years ago
Superfreak3 wrote:Like I've said, I'm a major newb

Don't know how major,... so here goes.

"Don't breathe the smoke/ fumes. Bad !! 🙂


Reply
Page 6 / 7
Share: