New Single String P...
 
Notifications
Clear all

New Single String Pixel controller

85 Posts
15 Users
0 Reactions
32.9 K Views
komby
Posts: 871
Topic starter
(@komby)
Prominent Member
Joined: 14 years ago
FrankAZ wrote:Very interested in seeing where this heads - I have a potential "project" that this would work out for. I am looking to have a master DMX/E131 controller setup - and have 10-15 "mobile" units that need to receive the signal. The goal is to have each unit with 150 pixels on each unit. As of right now - I plan on each unit to play the same pixel data.

Frank, I think we are there already(for ws2801). Combining these receivers with the e1.31 transmitter I linked to in the first post.

I'm still cracking on the fastspi2, to that extent, I had an idea today -Dangerous..... hey, i left 4 pins on the left hand side unused, maybe those can run a second string ? Likely would need to inject power to those though.


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

I had been thinking about making up a circuit board very similar to this: bare bones ATMega328p with a regulator and socket for the nRF24L01+, and connections for power and pixel connector, plus some additional I/O lines broken out. (But I'm not familiar with PCB editing, so I was also considering using the Arduino Pro Mini with hookup wire between the two, both tied to a wooden or plastic stick). Anyway, it's great that you are creating something with almost exactly that spec.

One difference was that I was thinking to see if I could get it to fit in 1", PVC pipe (3/4" would be even better, but hard to pull off). So I was thinking of orienting the 2x8 socket such that the nRF24L01+ stuck out the short end, making the joined pair longer but still not very wide. My thought was that some pipe and an end cap could protect the electronics and the connectors, using something stuffed in the bottom to keep out spiders and splashes (foam rubber? packing peanuts?).

Any chance of a different socket orientation in a later version?

How were you thinking to mount these, if used outdoors?

I believe that your design should also run 12V pixels, if the regulator can handle that input. I intend to use different connectors on 12V and 5V pixels, but otherwise they can be driven by the same 5V clock and data lines.

How many amps do you think the circuit traces can safely handle (between the power in jack and the pixel connector)?

I see you are running at 3.3v/16MHz. Jeenodes seem to be pretty successful in running in that configuration, even if it's out of spec.

I was torn between running the ATMega at 5v and 3.3v. Obviously simpler to interface to the nRF24L01+ at 3.3v, but I was wondering if the 3.3V ATMega I/O would successfully drive all the various pixels I have or am interested in (2811/5v, 2801/5v, 2801/12v, 1804/12v, 8806/5v, 3001/5v, 1829/5v, etc) or whether it would need a 5v buffer chip or transistors.

I was somewhat tempted to try to run at about 3.9v, which is within spec for the nRF24L01+ (might even boost the range), brings the ATMega closer to its spec for 16 MHz operation, and gives a little better noise margin for driving the pixels.

Running a Uno clone at 5v, I've been able to run 100 12v 1804 pixels at the end of a 40' 16ga feed wire; I guess the 40ma drive of the ATMega does pretty well. I'm guessing that it might not be as robust at 3.3v, but for the RF mode, typically the processor should have a relatively short wire to the first pixel.


Reply
komby
Posts: 871
Topic starter
(@komby)
Prominent Member
Joined: 14 years ago

I had set the challenge to myself to see if i could get two of them on a 5x5 cm PCB

so the current pcb width (.98") would work for schedule 40 (1.029") Its actually a bit thinner than it because i'm splitting them with a bandsaw.

but you are right the radio in its current location would prevent it. I could do a different version that moves the radio to the end and puts a row header all on one side.
I am already planning on re-doing the serial header side to make it one continuous row of pins for simplicity and expand-ability because I am working on a "sidecar" type expansion card which will be take advantage of the serial header and extra pins when not in use for programming. Things I have in mind as sidecars - rs485 + 8p8c connector... hrm ... what could we use that for 🙂

The other thing you could do is not use female headers for the radio. Instead use male headers (or a box header) and a 2x4 ribbon cable. I am planning on doing that with the PA boards so that they can mount easily and have a clean connection to the chip.

ok, regarding 3.3, 5v, 12v. Yes, I am running the atmega out of spec just like the jeelab. This board really is just a shameless bite on the jeelab with a different radio. Also similar to the sandevices 681 controller. I seem to recall in a thread about that controller that Jim said something like "I have never encountered pixels that couldn't be driven from 3.3 volts" which may have changed since '11 but led me to think that it would be ok to run with 3.3v.

How many amps? - 3a .. Ill double check my calcs again but I am pretty sure that the trace for vin/5v and GND are both 50mil. These are Elecrow boards with 1oz copper. I used those on various calculators to find that with a maximum temp rise of 12c that i would need a trace width of 49.54570868376314. If the trace width was insufficient a jumper from the dc connector to the 5v could be added right?(ghetto)

if someone finds that it doesnt work well at 3.3v I could make a 5v version that dropped it to 3.3 at the radio, I was trying to keep it simple.

How am I mounting them? Good question!

I am right now using dc wall wart for power. Their guts are a transformer and a 5v 3a linear regulator with a cooling heatsink.
( I wasn't sure about them but they are pretty cheap, enough so its tempting to use the transformer as a zc signal for creating a mod for the good old ssr-ez? )

If I keep using them, ill likely use a ta-200 to house it. The holes on the board could be used for screws but I was thinking the small zipties so i could ziptie them to the brick and only have to run an extension cord inside the ta-200

If one weren't so cheap and was using waterproof powersupplies then hey, use heatshrink !


Reply
komby
Posts: 871
Topic starter
(@komby)
Prominent Member
Joined: 14 years ago

the voltage regulator I am using is the

MCP1700-3302E/TO
http://ww1.microchip.com/downloads/en/DeviceDoc/21826b.pdf

it has a max input of 6v so it wouldn't work for 12v.


Reply
Posts: 124
(@frankaz)
Estimable Member
Joined: 14 years ago
komby wrote:Frank, I think we are there already(for ws2801). Combining these receivers with the e1.31 transmitter I linked to in the first post.

I'm still cracking on the fastspi2, to that extent, I had an idea today -Dangerous..... hey, i left 4 pins on the left hand side unused, maybe those can run a second string ? Likely would need to inject power to those though.

I've seen that - I'm going to be on WS2811s - but - I'm sure that'll just be something software to figure out - just trying to wrap my head around the transmitter part of things.


Reply
Page 5 / 17
Share: