Activity
 
Notifications
Clear all
nomis52
@nomis52
Trusted Member
Joined: Feb 6, 2010
Topics: 2 / Replies: 52
Reply
RE: YADA - Yat Another Dmx Adapter

The advantages are you're building on a well tested, mature codebase which is supported by an active development team. This means that once your chan...

11 years ago
Forum
DMX
Reply
RE: YADA - Yat Another Dmx Adapter

You should consider integrating the code with OLA. It should be pretty simple and it'll get you support for much more than just E1.31 Simon

11 years ago
Forum
DMX
Reply
RE: E1.33 RDMnet

Greetings from one of the authors of RDMNet. I've been posting to a G+ community explaining how it works: . If you're interested please follow along...

14 years ago
Forum
DMX
Reply
RE: It's sACN not E1.31

DynamoBen wrote:The same holds true, that is just an extension to the existing standard to add RDM functionality. SIDE NOTE: It is a shame more device...

14 years ago
Forum
DMX
Reply
RE: It's sACN not E1.31

DynamoBen wrote:Actually the real reason was to allow smaller microcontrollers to communicate on an ACN network. This enables vendors to make or updat...

14 years ago
Forum
DMX
Reply
RE: It's sACN not E1.31

DynamoBen wrote:Expect for the fact that it is built around ACN... (E1.17 for those that like numbers) Compare what ACN provides vs what E1.31 uses:...

14 years ago
Forum
DMX
Reply
RE: It's sACN not E1.31

DynamoBen wrote:I was part of this group for a time and when creating standards you always go by the standard's ID, which is E1.31. However when peopl...

14 years ago
Forum
DMX
Reply
RE: It's sACN not E1.31

DynamoBen wrote:So this has been bugging me for a while, everyone seems to want to refer to sACN (Streaming ACN) as E1.31. E1.31 is the specification ...

14 years ago
Forum
DMX
Reply
RE: E1.31 Protocol Discussions

timon wrote:Question for the E1.31 gru's. Can more than one source send commands to a single E1.31 controller as long as the don't try to control the ...

14 years ago
Forum
DMX
Reply
RE: DIYC official DMX Manufacturer ID

LabRat wrote: The problem at hand.. existing devices (REN series) to which some people want to convert to DMX. These devices don't have dip-switches, ...

15 years ago
Forum
DMX
Reply
RE: DIYC official DMX Manufacturer ID

LabRat wrote:My understanding of RDM is that it is a bi-directional protocol. We don't have that capability in most the hardware that I had thought to...

15 years ago
Forum
DMX
Reply
RE: DIYC official DMX Manufacturer ID

DynamoBen wrote:I agree with your position but also realize that implementing RDM in a uC is not a trivial task. I didn't claim it was trivial :), ...

15 years ago
Forum
DMX
Reply
RE: DIYC official DMX Manufacturer ID

LabRat wrote: The DMX stream then becomes 0x91 (note MFID= 0x586D ) For ProgAddress (CMD=) 0x91 For ProgSe...

15 years ago
Forum
DMX
Reply
RE: Lessons learnt DMX over IP.. Part(1) there is standards / there is no standards

mrpackethead wrote:Your example is exactly what happens out there in "real world". I know, that's what I asked it :). When faced with these ques...

15 years ago
Forum
DMX
Reply
RE: Lessons learnt DMX over IP.. Part(1) there is standards / there is no standards

And just to draw a comparison in the DMX world: Lets say I go out an buy some cheap 'DMX' strobes that only work with a narrow range of timing values...

15 years ago
Forum
DMX
Page 1 / 4
Share: