kbarre123
@kbarre123
Eminent Member
Joined: Oct 24, 2013
Topics: 0 / Replies: 20
Reply
RE: Backup, Backup and Backup....

I use git and GitHub for my Arduino sketches as well as my Vixen config/sequence stuff. I find its easier than making copies and wondering if I've got...

12 years ago
Reply
RE: Homebrew - 8 channel SSR- mini controller - Non-dimable

zparticle wrote:I'm thinking about adding a cat5e connection to the RX pin so I can send it values from a Vixen channel to trigger different patterns ...

12 years ago
Forum
Reply
RE: Newbie Arduino Start-Up Suggestions Guidance

Hi teemonie, I'd say go with either an Uno or a Mega; no Duemilanove. I went the Uno route b/c I already had two laying around from a school project...

13 years ago
Forum
Reply
RE: Vixen 3 and Arduino

Dont1982 wrote:Its like my computer isn't sending the signal to the arduino. I don't get it OK, after some success with Vixen 2, I decided to circle ...

13 years ago
Forum
Reply
RE: Newbie from UK needing help please!!!

masterful wrote:what code are u using for your setup if you dont mind me asking. masterful, Here's my code on github: . You're more than welcome to...

13 years ago
Forum
Reply
RE: Vixen 3 and Arduino

Do you have your channels in the sequencer mapped to the Generic Serial channels? Like, where you draw a line from one channel on the left to the Gen...

13 years ago
Forum
Reply
RE: Newbie from UK needing help please!!!

It'll work without the uart. I just tested it. It should work with the uart too though, lol. IDK, may be worth a shot; you may have a gremlin in that ...

13 years ago
Forum
Reply
RE: Vixen 3 and Arduino

I recognize that code, its from zparticle, however I've noticed at least one typo (extra comma after CHANNEL12 in the channels array). Zparticle wrot...

13 years ago
Forum
Reply
RE: Newbie from UK needing help please!!!

Hey masterful, Just out of curiosity, have you tried just going straight into the Uno with the USB from your PC, bypassing your USB/serial converter?...

13 years ago
Forum
Reply
RE: Newbie from UK needing help please!!!

halfpinter69, I guess it was worth a shot! Man, I can't imagine why your COM port drops out only when your relays are under load. I guess there's a g...

13 years ago
Forum
Reply
RE: Arduino code for christmas

It works with Vixen 2, I'm using it with an Uno. I prefer Vixen 3 too, but I couldn't get it working. We can get you running on Vixen 2 as a starter. ...

13 years ago
Forum
Reply
RE: Newbie from UK needing help please!!!

If I'm not mistaken, there's a "Settings" dialog box in Vixen 2 that lets you change what a 'low' and 'high' value are. There's a box next to 'low' a...

13 years ago
Forum
Reply
RE: Arduino code for christmas

Start Vixen 2 first, then plug in your Arduino. It should recognize it then. As for the picture, go to manage profile, add the adjustable preview from...

13 years ago
Forum
Reply
RE: Vixen 3 and Arduino

natale wrote:...and on the UNO, it was working only when set to 9600 baud for the serial read. Just FYI, I've got my Uno running at 57600 baud, whic...

13 years ago
Forum
Reply
RE: Arduino code for christmas

Dont1982, Vixen coordinates when the lights get turned on and off. The Arduino listens to Vixen, then tells the relays what to turn on and off. The...

13 years ago
Forum
Page 1 / 2