JCook
JCook
@jcook
Noble Member
Joined: Dec 18, 2013
Topics: 109 / Replies: 894
Reply
RE: Zero Crossing Circuit

MartinMueller2003 wrote:That is not a zero cross detector circuit. That is a Triac Driver circuit. Most times the circuit is wired with what you have ...

5 years ago
Topic
Replies: 7
Views: 3832
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

EL Wire typically operates in a range of internal voltage of 80-130+VAC (RMS), depending on the needs of the application. EL Wire can be operated at a...

5 years ago
Forum
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

kev wrote:If you have space for a 3.3v battery then you would have space for a 3.3v regulator. I used the MEGA's 5v power to run a 3.3v regulator for...

5 years ago
Forum
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

kev wrote:So, do you have it working now? yes with a Wemos D1R2 connected to a Mega, controlling 12 LEDs on a breadboard. Code in post #1 DOES NOT ...

5 years ago
Forum
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

MartinMueller2003 wrote:Are you sure the baudrate is correct? Also, you should only have esp GPIO 2 (Data Channel TX)->arduino rx. there is no Data Ch...

5 years ago
Forum
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

I think its correct. I tried the effects tab in the EPixelstick page to test as well.

5 years ago
Forum
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

i was using the sketch from post #4, I changed it to the one in post #1. It does a chase through all 12 of my leds then goes into the random patter...

5 years ago
Forum
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

angus40 wrote:tx-> rx ? i just edited my post yes I connected Tx->Rx3 and Rx->Tx3

5 years ago
Forum
Reply
RE: Success Modifying VictorPV Sketch to Accept Renard Protocol from ESPixelstick

I can't seem to get this to work... I loaded the ESPixelstick onto a WEMOS D1R2. and connected to a Mega R3. -connected the Tx->Rx3 (14) -conne...

5 years ago
Forum
Reply
RE: ESP8266 WiFi + Mega E131 Project

kev wrote:I can't help with any new programming. I had just been able to adapt existing sketches for the MEGA. In my opinion the ESPixelstick firmwa...

5 years ago
Forum
Reply
RE: ESP8266 WiFi + Mega E131 Project

MartinMueller2003 wrote:I'm saying that with ESPixelStick V4, you do not need the mega at all. A very inexpensive I2C board is all you need and you ar...

5 years ago
Forum
Reply
RE: ESP8266 WiFi + Mega E131 Project

kev wrote:Yes, that board can perform the functions you want, although I was not impressed by the wifi reception. Have you configured this board befo...

5 years ago
Forum
Reply
RE: ESP8266 WiFi + Mega E131 Project

kev wrote:I designed a shield for the MEGA which uses an ESP-01 using ESPixelstick firmware to receive E1.31 data and then output to the data ports fo...

5 years ago
Forum
Topic
Forum
Replies: 9
Views: 4261
Page 5 / 67