Activity
 
Notifications
Clear all
Christo25
@christo25
Eminent Member
Joined: Nov 9, 2018
Topics: 2 / Replies: 14
Reply
RE: Using LOR as DMX in xLights

OK it's still not working... Here's my controller configuration: Name: SanDevice e682. |. Protocol: E131 (Unmanaged). |. Address: 169.254.x.x (u...

6 years ago
Forum
Reply
RE: Using LOR as DMX in xLights

K-State Fan wrote:The LOR chart says the ID 06 is DMX 81 Sent from my iPhone using Tapatalk Dang... Math owns me again! Thanks for the heads up. ...

6 years ago
Forum
Topic
Forum
Replies: 5
Views: 3266
Reply
RE: xLights and SanDevices e682 - n00b Questions

angus40 wrote:The color order sound like it is GRB from what you say happens on your remote selection. Are you using the Prop Plug to Update firmware ...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

I'm quickly searching to figure out what a Prop Plug is....

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

So I received the tester today -- and the pixels "work". When I press the RED button on the remote, green lights up... and when I press the GREEN but...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

The store asked me to puchase a pixel tester to prove it was the pixels and they are blaming the controller. So... $7 for a tester... have to have $1...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

I've been corresponding with the seller and they are trying to blame the controller. I've shown them videos of other lights working fine and theirs n...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

angus40 wrote:I would lift the pcb up off of the housing and make certain it is insulated from touching it with double sided foam tape . Check the sol...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

The wiring looks correct -- the only thing I don't know is whether or not the R/G/B is reversed. I haven't tried BGR on the SanDevice for order yet.....

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

Thanks again for all of the feedback. This didn't come with a remote - so my intent was to use SanDevices controller, which has female pigtails... so...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

angus40 wrote:Ok Great . You have verified that the E682 works with the Pixel Strips 🙂 Are you certain that the flood is a RGB Pixel Flood ? Or is ...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

pmiller wrote:Did you power both sides of the 682? The 682 only needs 3 wires from the pixels, data, negative and positive power. Generally if the wir...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

MrDudeMan wrote:worry about getting test patterns in the 682 before you worry about vixen.. the config you listed will only output on connector 1-1 b...

6 years ago
Forum
Reply
RE: xLights and SanDevices e682 - n00b Questions

angus40 wrote:Hi Christo25 Have you tried connecting your pixel strips and did they work ? I would suggest updating the firmware on the e682 to the l...

6 years ago
Forum
Page 1 / 2
Share: