lower intensity
 
Notifications
Clear all

lower intensity

11 Posts
5 Users
0 Reactions
4,088 Views
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago
[#55256]

Hello everyone, I tried and unfortunately I had no luck.
I created a show and all the elements are 100% intensity; Is it possible to lower the intensity of all the elements without having to enter one by one?

I use vixen 3 on the pc, 2 ESP32 in E1.31 and 2 Mega 2560 via USB (1 for pixel, 1 for relay).
I wanted to lower the intensity of all the pixels.

thanks


10 Replies
Posts: 409
(@dim-bulb)
Reputable Member
Joined: 9 years ago

If you are using ESP pixelstick firmware, you can lower the intensity on the controller. Under device setup, down near the bottom, you will see brightness. set it to .35


Reply
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago

Dim Bulb, thanks
yes on ESP32 i am using ESP pixelstick firmware ....
while for the Mega2560 there are no possibilities but to intervene on the elements?

it is also true that next year I will switch from the Mega 2560 to the ESP32. I want to allocate the two Mega 2560s to the future mega tree.


Reply
Posts: 409
(@dim-bulb)
Reputable Member
Joined: 9 years ago

For the props that are controlled by the mega, you can go under the layout tab, click on the prop, you should see a dimming curve option, the curve should be at 0, put it at -65, save then do a batch render, it will change all the sequences at once. Then set the esp in the ui.


Reply
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago

OK, thanks a lot.
I try to do as you told me


Reply
jeffu231
Posts: 2457
(@jeffu231)
Famed Member
Joined: 15 years ago
dim bulb wrote:For the props that are controlled by the mega, you can go under the layout tab, click on the prop, you should see a dimming curve option, the curve should be at 0, put it at -65, save then do a batch render, it will change all the sequences at once. Then set the esp in the ui.

This is the Vixen thread and this appears to be how to do it in xLights. For Vixen you need to add a dimming curve in the patching for the elements in the Display Setup. Give this a look.

http://www.vixenlights.com/vixen-3-documentation/setup-configuration/dimming-curves/


Reply
StickyWicket
Posts: 548
(@stickywicket)
Honorable Member
Joined: 14 years ago

If you are using FPP you can install the brightness plugin and lower it that way.


Reply
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago

Thanks everyone for the advice,

unfortunately for now I am not using FPP, I am still at the beginning and I am learning slowly;
my show setup is still primitive, compared to yours.

@Jeffu231:
you're right, dimbulb's indications weren't exactly for Vixen, in fact I had tried
to dimming curve in the patching for the elements in the Display Setup but but I was not saved the curve in reference to the elements controlled by the Mega (gave me a message:0 Dimming Curves created, 0 cinfigured, and 0 skipped).
Then I created an attenuation curve in the sequence and I put the ESPpixelstick back to 100%.

It will not be the best system but it should work on everything .... tonight I try.


Reply
Posts: 418
(@richienorthcott)
Reputable Member
Joined: 7 years ago

Dimming curves are your friend. If you don't have any - set up in the curve library first from sequence editor. Call it 'dimming curve' for example. It's also worth using the gamma curve as per the instructions, since this will make the actual dimming appear much more linear when you adjust brightness from 0 to 100% in your sequence. e.g.

Pow(x/100,2.2) * 80 for an 80% gamma corrected cure

When you add the curve, select all the element(s) you want to add it to. You can select the parent node, it will be added to all children. Choose the 3rd option from the dialog (Insert a new dimming curve after the element). From my experience you need this even when setting up new ones. To verify, pick a single node and the corresponding output in the controllers then you can switch to 'graphical view' to confirm everything is set up correct. If you use a linked library curve you can adjust it at any time in the sequence editor and it will adjust the brightness of your whole display. I run mine at 40% output normally. Be warned of selecting all nodes or all controller outputs, this can make the graphical view too complex to load.

You can also add a 'debugging values' output controller to view the actual byte values being sent. It'a possible to patch a pixel to more than one controller output (or 3 I should say for RGB), just select 'use all available patch points' under 'patching options'/. So you could try a 50% white output which would give you 127,127,127 without a dimming curve.


Reply
Posts: 167
 gb70
Topic starter
(@gb70)
Estimable Member
Joined: 6 years ago

Thanks for everything
created the new curve and selected the 3rd option, now it has recognized the attenuation, also from the graphics now I see the "dimming curve".

perfect, I intervened again on the dimming of the ESP32.


Reply
Page 1 / 2
Share: