Fog Machine Trigger
 
Notifications
Clear all

Fog Machine Trigger

20 Posts
6 Users
0 Reactions
6,281 Views
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago
[#39056]

Hey folks. I haven't done any work in Vixen yet but I also haven't seen any references to what I want to do either.

I have a fog/smoke machine. Primarily used around Halloween. It has a rocker switch on a cable dongle to turn the output on and off. It, of course, cycles as its not a constant output caliber machine. When its powered, it pre-heats the chamber then when the rocker is thrown, it will immediately emit smoke. Leave the rocker on and it will recycle as soon as the chamber heats again.

What I would like to do is rig up a SSR, or even an old school DPST relay to fire the smoke at a specific time in the sequence.

Is this possible with Vixen? And if so what interface hardware would I need to trigger the SSR or mechanical relay. I can handle wiring up the coil/trigger and powering it. What I need is info on what sort of controller I would need that Vixen can trigger.

I am new at this so maybe I am grabbing more than my plate holds but I got so many ideas floating around in my head. If I don't work on some of them my head will explode. I ordered an e682 PL1 kit but don't have it yet so I am running with no hardware at the moment.

This is unlikely to make it for Christmas but I want to have it for Halloween next year.

So..
Vixen > PC > ??? SSR/DPST > Smoke-Rocker
??? ==

I am sure someone here has worked out how to trigger off/on 120v devices.


19 Replies
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

You'd need a controller of some sort that vixen can communicate with. Then the output of that controller may or may not need a relay or SSR to interface with the fogger. It really depends on the circuitry in the fogger' remote. It may be contact closure or it may be open collector. You'd need to determine that before deciding hardware.
Since it's just a single output id be looking at what existing controller outputs you have that can be adapted to work with the fogger.

--Jon Chuchla--

Sent from my iPhone using Tapatalk


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago
jchuchla wrote:You'd need a controller of some sort that vixen can communicate with. Then the output of that controller may or may not need a relay or SSR to interface with the fogger. It really depends on the circuitry in the fogger' remote. It may be contact closure or it may be open collector. You'd need to determine that before deciding hardware.
Since it's just a single output id be looking at what existing controller outputs you have that can be adapted to work with the fogger.

--Jon Chuchla--

Sent from my iPhone using Tapatalk

Thank you. I am pretty sure I am up on all that. I am not concerned with the fogger circuitry. Whatever it is I guarantee that a mechanical relay will take care of it since the mechanical switch does it came with. I can determine if a SSR/SCR/TRIAC/FET will work in lieu of a mechanical relay later. What I need to know is WHAT the controller is I am looking for to control the relay? I don't know what to search for, what terminology to feed google or the forum search here.

I don't think the e682 is capable of doing this. It won't do dumb RGB strings, only pixels, so I doubt seriously it can control a single binary channel. What controller mechanism am I searching for? Is it something DMX I should be searching? Is there another single on/off output controller technology or brand I can search for? I just don't know what Vixen is capable of controlling nor what options are out there to get this done. I am trying to reserch as much as possible before I start poking and prodding at my new hardware.


Reply
johnpdo
Posts: 102
(@johnpdo)
Estimable Member
Joined: 15 years ago

I did it here:
http://www.halloweenforum.com/halloween-props/145702-my-monster-box.html

Used a miniren 4xb http://digwdf.com/store/product.php?id_product=13

a 110 coil dpdt at amazon HH52P 110/120VAC Coil DPDT 8 Pins Electromagnetic Power Relay w DYF08A Base

worked very well. Hacked the remote to find the wires that close the circuit to make smoke (there were only 3 wires, and 2 need to be attached to the coil)

here's the youtube video:

have fun!

Doc


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

In that case any controller than can drive a relay will work. It could be a common Renard, or even an arduino. You'd then choose the appropriate output module for your controller type and patch it accordingly. You'll probably end up using either s set level or custom value effect in your sequence to do the triggering.

--Jon Chuchla--

Sent from my iPhone using Tapatalk


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago
johnpdo wrote:I did it here:
http://www.halloweenforum.com/halloween-props/145702-my-monster-box.html

Used a miniren 4xb http://digwdf.com/store/product.php?id_product=13

a 110 coil dpdt at amazon HH52P 110/120VAC Coil DPDT 8 Pins Electromagnetic Power Relay w DYF08A Base

worked very well. Hacked the remote to find the wires that close the circuit to make smoke (there were only 3 wires, and 2 need to be attached to the coil)

here's the youtube video:

have fun!

Doc

Hey! Cool beans! How is it controlled? Is that a WiFi board on it? I like the jumping action you got going on. How long does it run on that tank before you have to recharge it?

+1 for using the HM monolog! A fave of mine and the granddaughters.

I picked up a Korean war era blood transport box off craigs list last year (OD green and is stenciled with "Human Blood" on the sides/top) complete with ice container and rack but I can chuck those internals and create a box like you have there out of it!

Anyway, could this be used?
http://www.holidaycoro.com/3-Channel-DMX-Controller-for-RGB-Lights-12v-DC-p/37.htm

I know thats an analog 3 channel controller, but couldn't I drive a 12v coil or SSR with a diode de-quencher? Sequence it either full on or full off I suppose no?


Reply
johnpdo
Posts: 102
(@johnpdo)
Estimable Member
Joined: 15 years ago

I controlled it with vixen wirelessly to the miniren 4xB . Vixen also ran the program for my organ playing skeleton Quartet. It was a lot of fun! The 4xb runs wireless with an xBee module.
The air tank was just more storage, as I used an air line from a small compressor to attach to it. The 4xb also triggered the air valves for the air cylinders to move the box. Made the box out of an old wood pallet. I probably should have documented this better with the build on the forum 🙂

Sent from my SM-G900V using Tapatalk


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago
jchuchla wrote:In that case any controller than can drive a relay will work. It could be a common Renard, or even an arduino. You'd then choose the appropriate output module for your controller type and patch it accordingly. You'll probably end up using either s set level or custom value effect in your sequence to do the triggering.

--Jon Chuchla--

Sent from my iPhone using Tapatalk

Thats getting to the info I am asking for. "Renard". I can search for that and learn what it does!

How would I sequence an Arduino? I have an Uno. I also have several RasPi's.


Reply
Wolfie
Posts: 2225
Topic starter
(@wolfie)
Noble Member
Joined: 11 years ago
johnpdo wrote:I controlled it with vixen wirelessly to the miniren 4xB . Vixen also ran the program for my organ playing skeleton Quartet. It was a lot of fun! The 4xb runs wireless with an xBee module.
The air tank was just more storage, as I used an air line from a small compressor to attach to it. The 4xb also triggered the air valves for the air cylinders to move the box. Made the box out of an old wood pallet. I probably should have documented this better with the build on the forum 🙂

Sent from my SM-G900V using Tapatalk

Ahh, the tank is simply an accumulator. I figured the 4xB controlled the air valves too. Since the 4xB is a receiver, what is the transmitter? Is it a WiFi or bluetooth? Or does it require a specific transmitter to send commands? I guess I got some reading to do... Found this: https://www.sparkfun.com/pages/xbee_guide


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

At this point your best bet is a Renard board. There's too much learning curve to make an arduino work and it doesn't sound like you're there yet. Head over to diychristmas.org and look at the digwf store. He usually had small Renard boards in stock.
Renard is a category. There's many board designs that fit various form factors and channel counts. But they all use a common and standard communication protocol to receive serial data from the computer. Some of dirks mini-ren designs are designed to use an xbee wireless serial link. But you can also use them in a wired configuration.

--Jon Chuchla--

Sent from my iPhone using Tapatalk


Reply
Page 1 / 2
Share: