E682 Controller Set...
 
Notifications
Clear all

E682 Controller Setup

4 Posts
3 Users
0 Reactions
1,988 Views
cnbales
Posts: 503
Topic starter
(@cnbales)
Honorable Member
Joined: 15 years ago
[#34803]

I need a little help getting one of my E682s setup in V3. I saw a post that I believe got me close to where I need to be, but I just want to make sure. I have attached the picture to show my setup for this E682. I just need to know how to configure this in the Controller Setup screen in V3.

E682 a setup

Also I have a few questions regarding the Controller Setup screen:

1. Does Vixen only support multicast? This won't be an issue for my setup, just curious at this point
2. I watched tutorial videos for V3 and there was mention of identifying the ip address for the controller. Where do I input the ip address?
3. What is a scenario that you would use Max Repeat Count with an integer >0?
4. What is Display ALL warnings/Errors and wait for OK used for?
5. What is Gather statistics and display at end of session used for?
6. Which multicast should I be using, Loopback or Local Area Connection?

Controler setup

3 Replies
Tegbert
Posts: 276
(@tegbert)
Reputable Member
Joined: 13 years ago

You right click on the destination box and put your ip address in there and once submitted it will be in the drop down.

Travis


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

1. Does Vixen only support multicast? This won't be an issue for my setup, just curious at this point

Unicast is supported, but multicast is encouraged since it's the primary method intended by the sACN specification. To add a unicast destination, right click in the destination dropdown

2. I watched tutorial videos for V3 and there was mention of identifying the ip address for the controller. Where do I input the ip address?

You only need to input the IP address if you're using unicast. That's why multicast is preferred - because it requires less configuration and therefore is easier and quicker to use. You don't need to worry about addressing.

3. What is a scenario that you would use Max Repeat Count with an integer >0?

These settings are used to reduce network traffic when there's nothing going on. Default is 0 which means that vixen will continue to send data regardless of whether it is changing. If it's greater than 0 this option will send the last frame that's changed this many times before stopping the output. Max suppress count will allow you to only suppress so many packets before it sends another one just to make sure everything stays in the same state.

4. What is Display ALL warnings/Errors and wait for OK used for?

This attempts to collect warnings and wait for your confirmation before closing.

5. What is Gather statistics and display at end of session used for?

Similar to above

6. Which multicast should I be using, Loopback or Local Area Connection?

Local Area Connection will send it out the "Local Area Connection" port, which is usually your wired LAN port.
Loopback will send it back to this computer. This is useful if you're using a tool like sACNview to monitor the data while inspecting for problems.
You may also have other interfaces listed here as well depending on what network interfaces are installed on your computer.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

Clusters 1-3 will be all the same string settings, 4 strings, 25 pixels.
Cluster 4 has to be 4 strings of 44 because 44 is the longest string. This comes out to 528 Channels.
so your grand total is 1428. That's nicely under 3 universes.

Cluster 1 will start a U1 C1
Cluster 2 will start at wherever 1 ends +1
Cluster 3 will start at wherever 2 ends +1
Cluster 4 will start at wherever 3 ends +1

SO in the sACN output controller, set up 3 universes. (I like to start at 101) number the universes 101, 102, 103 (or any 3 numbers you like, so long as they match in the controller)
101 starts at 1 with a size of 510
102 starts at 511 with a size of 510
103 starts at 1021 with a size of 408

Now when you patch you just need to line up your elements with the appropriate output channels.

Make sense?


Reply
Share: