I have Vixen 3 driving Renard SS24's. I have two giant candy cane elements each with 1 white LED string and two red LED strings. I have library dimming curves and color handling for each string/channel so white is white and red is red.
One of the white channels shows up as red in the Sequencer and in the preview. As such I'm not getting the white LEDs on one of my canes. I've triple checked the color handling and patching under Setup Display and all appears correct. I've re-patched that element and still no change.
It is as if something is overriding the color handling. What could it be? 🙁
I had something similar when I create my Halloween costumes. I changed one of my colors and it was correct in the sequencer and preview but behind the scene it was still the old color so it never turned on. took me awhile to figure it out.
try this.
Go into Display setup.
select the element that is showing up red.
click on graphical view.
Double-click the color breakdown and see if in the "Color Breakdown Filter Setup" form it shows the correct color.
If it only allows you to choose red in the sequencer and it is supposed to be white, then something is likely wrong with the color handling because that is where the sequencer gets the color from. You can select the element in the sequencer and then in the properties box in the lower left edit the color item. That should bring up what it is set to and you can check it there one element at a time.
jeffu231 wrote: You can select the element in the sequencer and then in the properties box in the lower left edit the color item.
Did you mean to say "Display Setup" and not "sequencer"? I don't see any properties box in the sequencer.
Also I have run into the issue where I changed the color in the properties box (in display setup) I had issue with that string not working I found out that if I go into the Graphical patching mode then click on color breakdown, that color did not update. I just did this again and here are the results.
here are the steps I followed
selected the element
clicked on color in the properties box
clicked configure property
change the element color as below to Red.
exited the Display setup.
re opened display setup.
selected the same element as above
selected graphical View.
double clicked the color breakdown and it came up as blue, which is the color I started with.
When I had this issue before, the fix was to change the color handling in the graphical view. While it showed the correct color in the sequencer, it would not output to my lights until I fixed it in the graphical view.
Maybe this is a bug?
Sorry, I did mean Display setup not the sequencer. Both the properties edit and the graphical setup should do the same thing. I can look to see if there is some type of bug there. I have not had to do this myself in a long time and it does not come up very often.
jeffu231 wrote:Sorry, I did mean Display setup not the sequencer. Both the properties edit and the graphical setup should do the same thing. I can look to see if there is some type of bug there. I have not had to do this myself in a long time and it does not come up very often.
When I create my Halloween costumes with EL Wire which is single color, I ran into this issue. I had one output not working and I happen to check the graphical because I changed that outputs color in the properties and it stopped working. So I think something is going on there. You want me to log it in the bug tracker?
JCook wrote:I had something similar when I create my Halloween costumes. I changed one of my colors and it was correct in the sequencer and preview but behind the scene it was still the old color so it never turned on. took me awhile to figure it out.try this.
Go into Display setup.
select the element that is showing up red.
click on graphical view.
Double-click the color breakdown and see if in the "Color Breakdown Filter Setup" form it shows the correct color.
I triple checked the color, toggled to a different one then back again. I deleted the filters, added back, still no joy.
My fix was to simply delete the element and recreate it, add filters, and patch. Now I'm back in business.
I do see some issues with editing the color property and it not working correctly. To edit them manually you would have to edit the color property and the color breakdown from the graphical screen. But because the color property edit does not work correctly you can't edit both parts correctly. However if you use the color handling wizard on the elements to overwrite the existing ones, I don't see any issues with that working correctly. It will update both parts. I tested it several different ways and it looked to work correctly for me. You will have to reopen each sequence if you are using single colors that you change so the colors can be updated to the new color.

