Gremlin is back
 
Notifications
Clear all

Gremlin is back

21 Posts
5 Users
0 Reactions
10.3 K Views
Aurbo99
Posts: 2804
Moderator
Topic starter
(@aurbo99)
Member
Joined: 19 years ago

Re-Checked all my cables, connections etc.

Checked my brick psu and it was pushing out 6.57 vdc at the 5vdc setting, replaced it with a new one.

Now pushing 5.35vdc most of the random gliching has settled down,

I completely swapped out my #1 SSRoz unit, but the main error with that still remains. It will flash back on and stay on after sequences are over. even with an all off script running

I can move all my SSROZ's around the Grinch and its consistantly A group channels 1-4 that remain on.

Is it possible to isolate the first group 1-4 channels and block them completely off the setup? If so how? Maybe blocking off 1-4 channels and adding 4 to the count might work


Reply
Posts: 22
(@jetmech)
Eminent Member
Joined: 19 years ago

You may have better luck if you post this in the Grinch Forum.
http://www.doityourselfchristmas.com/forum/viewforum.php?f=31
As busy as things are this time of year it's hard to keep up with all the posts on the whole site. A lot of people will never see this thread.

John


Reply
Posts: 171
(@biffklg)
Estimable Member
Joined: 19 years ago

I think it has something to do with the fact that your boards are not completely populated. I would finish building your boards and then see how things go..


Reply
FireGod
Posts: 655
(@firegod)
Honorable Member
Joined: 19 years ago

The cable between the PC and the board should be as short as possible (5 to 10 cm).

Also try different voltage levels, 4.1 to6.0 VDC.

Make sure ANY electrical noise is at a distance (florescent lamps, fans, motors, any appliances.

Put a very large capacitor (>1000 uF) on the 5 VDC supply to make sure it is nice and smooth.

Do not use a laptop PC, only use a desktop.

Make sure the ground for all the components AND the PC case are tied together.

The 595 I/C is very susceptible to external noise.


Reply
FireGod
Posts: 655
(@firegod)
Honorable Member
Joined: 19 years ago

It does not matter if you have not populated the rest of the board. However, make sure that the plugin is configured for the EXACT number of channels that are populated.


Reply
Aurbo99
Posts: 2804
Moderator
Topic starter
(@aurbo99)
Member
Joined: 19 years ago
FireGod wrote:The cable between the PC and the board should be as short as possible (5 to 10 cm).

Also try different voltage levels, 4.1 to6.0 VDC.

Make sure ANY electrical noise is at a distance (florescent lamps, fans, motors, any appliances.

Put a very large capacitor (>1000 uF) on the 5 VDC supply to make sure it is nice and smooth.

Do not use a laptop PC, only use a desktop.

Make sure the ground for all the components AND the PC case are tied together.

The 595 I/C is very susceptible to external noise.

Wow! 2-4 inches for the computer to grinch? I'll make one up and try it.

No to any electrical noise,

I'll increase my 100uf to a 1000uf cap

Yes to a desktop, just flashed up my old one to dedicate to the display.

I'll add an external grounding cable to the PC case. Ground the Grinch to the case as well?

Using Allegro IC's on a Grinch board with the 595 plugin on Vixen

Thanks, I'll try it all. Lights are behaving for the most part. Still random glitching but its not overly noticable at the momnet as I am using a random display sequence to hide it between mapped sequences

I did have Background music enabled, but dont ever recall setting up any.
Went back through my individual channel strings and corrected an oversight of a once spare channel not properly identified. Changed all of channel names as a result.


Reply
FireGod
Posts: 655
(@firegod)
Honorable Member
Joined: 19 years ago

Yes, ground the Grinch to the PC case just to make sure everything has the same ground reference.

Noise on the parallel port is a problem.


Reply
Aurbo99
Posts: 2804
Moderator
Topic starter
(@aurbo99)
Member
Joined: 19 years ago

So, just run a wire from the round hole on Grinch J2 pin and run it to the PC case?

I would have thought that pin 3 on your "In" RJ45 connection is supplying the grounding from pins 18thru25 on the LPT port.


Reply
FireGod
Posts: 655
(@firegod)
Honorable Member
Joined: 19 years ago

I have found that the PC case is not always connected to the LPT port ground. I guess just do what you need to do or test it with an ohm meter. It is one of the things I would do if I was having the same problem.

My assumption is that Vixen is not sending these commands. I am under the assumption that it is noise from the LPT port, nd I would be doing everything I could to reduce or eliminate that noise. Having everything with the same ground reference is a basic step to eliminating noise.


Reply
Aurbo99
Posts: 2804
Moderator
Topic starter
(@aurbo99)
Member
Joined: 19 years ago

Grinch group "G" , my last SSROZ group was acting up badly. I moved the connection to "H" and left "G" without a connection. The system began to behave. I'll inspect "G for a bad solder/trace/connection after the display is taken down.

I took advantage of the mild weather today to inspect all cables, test them in the yard, and all is good out there.

FYI Red plastic Folgers Coffee cans work great as weatherproof shelters for the SSRO'Z modules, you dont really notice them under a mini tree or lined up behind the real bushes.

Confirmed and corrected a few mis-identified channels that may have caused confusion.. when you look at Candy_Cane_1 and trigger it on, and Mini_Tree_16 ignites.. something got mis labeled. Fixing that took some of the apparent glitching out as well.

Took my spare computer with a 3" cable from computer to Grinch, set it all up in the garage and ported all my sequences to it. Its running now with very minor gemlins. Channels 1-4 still ignite randomly. All_Off_Script handled them all so far.

Merry Christmas everyone!


Reply
Page 2 / 3
Share: