Notifications
Clear all

Support for D-light

93 Posts
23 Users
0 Reactions
86.6 K Views
kostyun
Posts: 2178
Guest
(@kostyun)
Member
Joined: 20 years ago

Yes, it means the twinkle and flickers are handled in hardware rather than the application sending it.


Reply
Macrosill
Posts: 9739
(@macrosill)
Member
Joined: 20 years ago

Then am I correct in assuming that the software must send out some kind of trigger for these special effects to occur? And if so any idea what it is? Is there no way to send some type of data via dmx that would trigger these effects? Maybe a special dmx-dlight plug in that could do it?

The hardware does not decide on its own to start a twinkle effect.


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Earlier readings shows that the D-Light is using a bootloader. I suspect we could create a REN firmware image that would load over the serial bootloader.
Then without changing the hardware at all, it could be made to talk REN.
Unless there is something highly proprietary about the bootloader (I'm guessing not).

fkostyun wrote:One thought that comes to my mind would be to create a daughterboard that would plug into the PIC slots (as long as they are removable) to adapt/change them to the Renard Spec. I would draw something like this up - but - don't have a board to test with.

As I look at the boards - it appears that they use 18F pics for each of the 8 channels.

Of course, if someone wrote an dlight (lor) plugin for vixen.... that would also solve the issue!


Reply
Posts: 122
(@mrchristmas2000)
Estimable Member
Joined: 19 years ago
Macrosill wrote:Then am I correct in assuming that the software must send out some kind of trigger for these special effects to occur? And if so any idea what it is? Is there no way to send some type of data via dmx that would trigger these effects? Maybe a special dmx-dlight plug in that could do it?

The hardware does not decide on its own to start a twinkle effect.

Hasn't a lor/d-light plugin for Vixen been discussed somewhere before?

There are currently 3 programs that I am aware of that can control Lor/D-Light boards, LOR, Aurora, and Light Show Pro. A good programmer should be able to capture and ananlyze the data stream then design a Vixen driver. Maybe thats too much of a simplification.

Tom


Reply
Posts: 1062
 Ronp
(@ronp)
Noble Member
Joined: 20 years ago
Reply
Posts: 122
(@mrchristmas2000)
Estimable Member
Joined: 19 years ago

Right from the horses mouth.....


Reply
kostyun
Posts: 2178
Guest
(@kostyun)
Member
Joined: 20 years ago

Well, one of my goals for "next year" is to get into programming again.. been out for 10 years.....


Reply
Posts: 40
(@reidfo)
Trusted Member
Joined: 17 years ago

I have just released an alpha version of a LOR / D-Light plugin for Vixen. It hasn't had much testing yet, but I welcome any comments you might have.

See this post for the link: http://doityourselfchristmas.com/forums/showthread.php?t=8149

EDIT: Direct link is at picsil.com/vixen


Reply
Posts: 1062
 Ronp
(@ronp)
Noble Member
Joined: 20 years ago

Nice work hope this make alot of people happy....


Reply
Posts: 14
(@tonyjmartin)
Active Member
Joined: 19 years ago
Ronp wrote:Nice work hope this make alot of people happy....

Me! Me! It makes me happy! Now...once we buy a house here in Michigan, then I can fire up my 200+ channels with Vixen for the holidays. Most likely fall 2010, as we just moved here from Wyoming.


Reply
Page 9 / 10
Share: