Notifications
Clear all

Support for D-light

93 Posts
23 Users
0 Reactions
86.6 K Views
Posts: 737
(@joneslights)
Prominent Member
Joined: 19 years ago

Would Ernie's plan work? I was thinking of grabbing a d-light board and test it.


Reply
Posts: 19
(@rjmcnay)
Eminent Member
Joined: 18 years ago
joneslights wrote:Would Ernie's plan work? I was thinking of grabbing a d-light board and test it.

What is Ernie's plan?
I already have a d-light board and really like it.
I am thinking about expanding it.


Reply
Posts: 737
(@joneslights)
Prominent Member
Joined: 19 years ago
rjmcnay wrote:What is Ernie's plan?
I already have a d-light board and really like it.
I am thinking about expanding it.

ErnieHorning
Member

Join Date: May 2007
Location: Apple Valley, MN
Posts: 415
Re: Support for D-light
It shouldn’t be too difficult to put Renard into a PIC18F2420 and plug it in to your D-Light board. Nobody looses, copyrights are still intact and your board then works with Vixen.


Reply
Posts: 19
(@rjmcnay)
Eminent Member
Joined: 18 years ago
joneslights wrote:ErnieHorning
Member

Join Date: May 2007
Location: Apple Valley, MN
Posts: 415
Re: Support for D-light
It shouldn’t be too difficult to put Renard into a PIC18F2420 and plug it in to your D-Light board. Nobody looses, copyrights are still intact and your board then works with Vixen.

Ok: I am a newbie at the PIC stuff. How do I put Renard into a PIC18F2420.
This chip (2) I already have on my board. One other posting says that Darryl needs to give the pin outs. So what am I missing.


Reply
Posts: 737
(@joneslights)
Prominent Member
Joined: 19 years ago
rjmcnay wrote:Ok: I am a nebie at the PIC stuff. How do I put Renard into a PIC18F2420.
This chip (2) I already have on my board. One other posting says that Darryl needs to give the pin outs. So what am I missing.

You'll need a pick programmer and a copy of the hex file (on the Christmas Wiki) Pickit 2 is the most used programmer. I wouldn't use the chip on the board as, if something goes wrong you'll lose your D-light code.

The pinouts are so a cable can be made to connect vixen to the d-light.

But, LOR and d-light use the same pinouts I believe, so that is on the wiki as well.


Reply
Posts: 19
(@rjmcnay)
Eminent Member
Joined: 18 years ago
joneslights wrote:You'll need a pick programmer and a copy of the hex file (on the Christmas Wiki) Pickit 2 is the most used programmer. I wouldn't use the chip on the board as, if something goes wrong you'll lose your D-light code.

The pinouts are so a cable can be made to connect vixen to the d-light.

But, LOR and d-light use the same pinouts I believe, so that is on the wiki as well.

Another question or two.
Do you have a link or know where all of the above is on Christmas Wiki.
I believe I have the hex code for my PIC's.
Also, can we take this off-line some way.


Reply
Posts: 737
(@joneslights)
Prominent Member
Joined: 19 years ago
rjmcnay wrote:Another question or two.
Do you have a link or know where all of the above is on Christmas Wiki.
I believe I have the hex code for my PIC's.
Also, can we take this off-line some way.

Cable making http://www.doityourselfchristmas.com/wiki/index.php?title=Pinouts

Firmware
http://www.doityourselfchristmas.com/wiki/index.php?title=Renard_Firmware


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

You cannot use the Renard code as-is on the d-light boards. The .asm file will need to be changed to work with the d-light board. This is a task for someone who has good assembly language skills, knows the PIC assembly language, and has sufficient information about the d-light hardware. For such a person (Ernie may have had me in mind) it is not a huge task.


Reply
Posts: 737
(@joneslights)
Prominent Member
Joined: 19 years ago
P. Short wrote:You cannot use the Renard code as-is on the d-light boards. The .asm file will need to be changed to work with the d-light board. This is a task for someone who has good assembly language skills, knows the PIC assembly language, and has sufficient information about the d-light hardware. For such a person (Ernie may have had me in mind) it is not a huge task.

Well, there's the answer. Thanks! If you ever feel like tackling that (or any one else) let me know. I do not know enough about assembly to try to tackle it.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
P. Short wrote:... Ernie may have had me in mind...

I wasn’t pointing directly at you; though you seem to have the best qualifications on this site.

The majority of the code is already available and it should be a small task of modifying some register setups and changing port values. It think the boards are setup similar to that way the we’ve been doing it. I don’t remember how the zero crossing is implemented. I know that LOR uses an op-amp and maybe D-Light does too. The TRIAC circuit, I believe, is the same as ours.


Reply
Page 5 / 10
Share: