Output Plugin FT232...
 
Notifications
Clear all

Output Plugin FT232R - Microcontroller type PIC16F876A

10 Posts
6 Users
0 Reactions
6,334 Views
Posts: 4
Topic starter
(@dgshue)
Active Member
Joined: 17 years ago
[#8813]

Anybody interested in the FT232R output plugin (my first and hopefully last) for a Microcontroller type PIC16F876A.


9 Replies
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Is this using some non-standard comms protocol or using the FT chip in some unusual manner? AFAIK the FT232 appears much the same as any other serial interface to Vixen, once the appropriate FTDI driver is installed.


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:Is this using some non-standard comms protocol or using the FT chip in some unusual manner? AFAIK the FT232 appears much the same as any other serial interface to Vixen, once the appropriate FTDI driver is installed.

The FT232 can be used two ways as a virtual com port or as a standard USB device (the one you are referencing). Most folks use virtual com port, with that being the case any serial protocol should work fine...Phil's is worth a look. Alternatively if you want you can go the DMX route which also uses the FT232 (see the OpenDMX driver).


Reply
Posts: 48
(@bhilpert)
Trusted Member
Joined: 17 years ago

Can someone please give me instructions for an idiot on how to get the LOR kit - FT232R to work with Vixen

Does anyone have a output that works with the current vixen 2.1


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
bhilpert wrote:Can someone please give me instructions for an idiot on how to get the LOR kit - FT232R to work with Vixen

Does anyone have a output that works with the current vixen 2.1

You may want to post in the LOR area also:
http://doityourselfchristmas.com/forums/forumdisplay.php?f=66


Reply
Posts: 48
(@bhilpert)
Trusted Member
Joined: 17 years ago

I uploaded the plug in and it does not appear in the output options

Does this plugin work with LOR ethernet or usb plug

Or does this require a DMX connection?


Reply
Posts: 4
Topic starter
(@dgshue)
Active Member
Joined: 17 years ago

What are you working with there? This plug in is designed for a board like this,

http://denkovi.com/product/31/usb-16-channel-relay-module-rs232-controlled-12v-ver-1.html

You can find these on eBay, they're a small DIY board. Looking for some solid state to add to my setup. Not having any luck yet.


Reply
Posts: 9
(@amplebiz)
Active Member
Joined: 16 years ago

Can you please advise how to add it to vixen plug-in list ?

I copied the file to output folder, then launch vixen, it didn't show up. Did I miss something ?

Sorry for this low level question from a newbie.


Reply
Posts: 4
Topic starter
(@dgshue)
Active Member
Joined: 17 years ago

What version of Vixen, this has only been tested on 2.5.x. You could also try to remove the others temporarily to make sure your not over looking it. What type of board do you have, this is for a specific type of relay board I found on eBay.


Reply
Posts: 28
(@rmullins)
Eminent Member
Joined: 17 years ago

You have to go to the ftdi website and download the drivers for the FTDI232R. Once you have the drivers loaded plug in the FT232R and let the drivers install. I am currently using the FT232R to run my Halloween show and have not had any issues once I got the drivers installed. I just used the Enttec USB Output Pluggin.


Reply
Share: