Cannot make paralle...
 
Notifications
Clear all

Cannot make parallel port work

8 Posts
4 Users
0 Reactions
3,196 Views
Posts: 4
Topic starter
(@rocklobsta)
Active Member
Joined: 16 years ago
[#12338]

I've been trying to get vixen to control my parallel port, but no matter what I do, pins 1-13 are +5v, and 14-25 are ground. I'm starting to think the parallel port is malfunctioning, but I thought I'd check here. I've tried EPP and ECP, both with IRQ 5 and 7. All gave the exact same result.

Is this a software issue, or is it my computer?


7 Replies
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

Here's a cool program (just a Windows EXE) that will allow you to view all three parallel ports in real time.

You can even click on output pins the change their current state.

This way you can see if the port works and that Vixen can change it.


Reply
Posts: 529
 Josh
(@josh)
Honorable Member
Joined: 19 years ago

have you made sure the port is turned on in bios? also that bios is saving the settings.
I had an old Dell that i always had to fight to get to work.


Reply
Posts: 4
Topic starter
(@rocklobsta)
Active Member
Joined: 16 years ago
ErnieHorning wrote:Here's a cool program (just a Windows EXE) that will allow you to view all three parallel ports in real time.

You can even click on output pins the change their current state.

This way you can see if the port works and that Vixen can change it.

I'll give that a try. Thanks!

Josh wrote:have you made sure the port is turned on in bios? also that bios is saving the settings.
I had an old Dell that i always had to fight to get to work.

haha, yeah I made sure. Of course, this computer is a compaq, so you never really know with it.


Reply
Posts: 4
Topic starter
(@rocklobsta)
Active Member
Joined: 16 years ago

It only seems to be able to control pins 14, 16, and 17. Shouldn't it be 2-8?

EDIT: Weird... it doesn't actually change the output, it just displays it as changed. I guess this computer is just dead.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

1, 14, 16 and 17 are the four control bits for the port if that makes a difference. Do you have the orientation (left-to-right) of the pinouts correct - it's easy to get that backwards depending on which direction you're looking at it...


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
rocklobsta wrote:It only seems to be able to control pins 14, 16, and 17. Shouldn't it be 2-8?

EDIT: Weird... it doesn't actually change the output, it just displays it as changed. I guess this computer is just dead.

If pins 2-8 stay high, then yes I believe the port is bad. If it stays low, then it would be normal if configured for ECC. In ECC the outputs are open collector and would need to be pulled up, in which case it could be tested with an ohmmeter.


Reply
Posts: 4
Topic starter
(@rocklobsta)
Active Member
Joined: 16 years ago
ErnieHorning wrote:If pins 2-8 stay high, then yes I believe the port is bad. If it stays low, then it would be normal if configured for ECC. In ECC the outputs are open collector and would need to be pulled up, in which case it could be tested with an ohmmeter.

It didn't even have an option for ECC. Just ECP and EPP.

Well I guess it's time to go find another old motherboard. Thanks for your help.


Reply
Share: