ShiftBrite
 
Notifications
Clear all

ShiftBrite

16 Posts
7 Users
0 Reactions
5,068 Views
Posts: 577
Topic starter
(@photovor)
Honorable Member
Joined: 19 years ago
[#5576]

Found this today via hackaday.com:

Video:

http://macetech.com/store/index.php?main_page=product_info&cPath=1&products_id=1

"ShiftBrite is a high-brightness LED module containing red, green, and blue elements. It uses a simple clocked serial interface to receive a 10-bit brightness value for each color, resulting in over a billion possible colors. Each input is buffered and output on the other side of the module. This allows each ShiftBrite to repeat the signal to the next, allowing longer cable runs between elements without excessive loading of microcontroller I/O pins. ShiftBrite elements feature current control and automatic overtemperature control (an overheating channel driver will shut off until it has cooled). Each channel can also be adjusted with a separate current control register, for fine tuning of each LED if close brightness matching is necessary. The integrated voltage regulator powers the internal logic, allowing a single 5 to 9 volt supply rail to power the ShiftBrite chain."

For $4.99, pretty sweet deal.


15 Replies
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

It's down to $3.50 in Qty 250

And $3.74 at Qty 100.

Interesting.


Reply
Posts: 577
Topic starter
(@photovor)
Honorable Member
Joined: 19 years ago

Anyone up for a group buy? Just would have to come up with a good way of weatherproofing these, and I'd add them under my eaves/soffit.


Reply
rlilly
Posts: 993
(@rlilly)
Noble Member
Joined: 19 years ago

What's the difference between these and JEC's pixels?


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

JEC's pixels are DMX compliant.

This unit understands clocked serial data. So, it's only interesting from a idea perspective.


Reply
Posts: 577
Topic starter
(@photovor)
Honorable Member
Joined: 19 years ago

1. ShiftBrites aren't individually addressable. Meaning that you re-write the information to all of them at once, not just the one you want to change. (not DMX addressable)

2. These only cost $4.99, for everything (compared to $12), which come on a PCB with a header

3. ShiftBrites use one high-brightness LED

Each has it's own benefits and drawbacks. I prefer this method because of the cost, and how I plan to use them. Other people may feel the same way. A plugin could also be developed for these because its closest to how a 595 works.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

That should be doable on a DIY basis for less money. It is probably using the Allegro a6281 controller (or one of its siblings), which costs around $.78 in 1000-pc lots.


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago

Actually these are more like JECs point source pixel, which costs much less than the original pixel. I believe the projected cost on a 600 board run comes very close to this (or less).

Personally I like the DMX approach better than the serial approach due to the fact that with DMX if 1 pixel dies then the rest continue unaffected. But in a serial environment if 1 pixel dies all the following pixels also die.


Reply
Posts: 577
Topic starter
(@photovor)
Honorable Member
Joined: 19 years ago
P. Short wrote:That should be doable on a DIY basis for less money. It is probably using the Allegro a6281 controller (or one of its siblings), which costs around $.78 in 1000-pc lots.

Yep, he uses the A6281 chip. Figuring I have no way to etch boards, and program the chips, this is pretty reasonable to me. This was more attractive to me over the JEC pixels, because of the simplicity.

Just wanted to share my findings.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Those chips don't need programming...they are just another hardware chip.


Reply
Page 1 / 2
Share: