Im sure a lot of people here have heard of or own a buzz box.
I was wondering is there any designs out there for one a DIYer can do?
Are you talking about the one that sounds like a mosquito to drive away kids? If so, here you go - http://electroschematics.com/370/electronic-mosquito/
I'm sure they are not to hard to make - just have never seen the inside of one!
Previous discussion with photos.
http://doityourselfchristmas.com/forums/showthread.php?t=3689&highlight=buzz
phenagan wrote:Are you talking about the one that sounds like a mosquito to drive away kids? If so, here you go - http://electroschematics.com/370/electronic-mosquito/
no im thinking of a box to help fix mini strings
jrock64 wrote:Previous discussion with photos.
http://doityourselfchristmas.com/forums/showthread.php?t=3689&highlight=buzz
great thread did not see it BUT it seamed to end in 2008.... hope some one with electro knowledge pickes it up and runs to the finish line.
AH! Hadn't seen the old thread. Looking @ the photos & then the video on the website linked, it's not hard to guess how this is put together & works. The unit consists of two sections - the first just sends normal 110v through the string when the box is on. When the test button is pressed, the 110v is cut off and the second part of the unit is energized, which consists of a charge circuit pulsing a spark coil (probably a motorcycle one). This kicks a low current, high voltage (30KV) pulse across the string. This either fires the shunt in the bad bulb (same way a lightsaver goes, except that uses a piezo crystal to generate the spark) or if that fails, the spark jumps at the loose connection, creating the buzzing sound.
The discrete components shown in the photos are a triac, a resister, a diode, a capacitor (probably a motor cap) and an unknown one (the green item), which may be a MOV acting as a snubber to protect the triac. The triac is being triggered the AC cycle to dump the charge in the big cap across the coil, creating the spark. By doing it this way rather than just drive the coil via a 12v transformer, the spark duration is shorter, so the chances of killing a good bulb is reduced.
A variation of this circuit was found in cheap helium neon lasers in the 70's.
phenagan wrote:AH! Hadn't seen the old thread. Looking @ the photos & then the video on the website linked, it's not hard to guess how this is put together & works. The unit consists of two sections - the first just sends normal 110v through the string when the box is on. When the test button is pressed, the 110v is cut off and the second part of the unit is energized, which consists of a charge circuit pulsing a spark coil (probably a motorcycle one). This kicks a low current, high voltage (30KV) pulse across the string. This either fires the shunt in the bad bulb (same way a lightsaver goes, except that uses a piezo crystal to generate the spark) or if that fails, the spark jumps at the loose connection, creating the buzzing sound.The discrete components shown in the photos are a triac, a resister, a diode, a capacitor (probably a motor cap) and an unknown one (the green item), which may be a MOV acting as a snubber to protect the triac. The triac is being triggered the AC cycle to dump the charge in the big cap across the coil, creating the spark. By doing it this way rather than just drive the coil via a 12v transformer, the spark duration is shorter, so the chances of killing a good bulb is reduced.
A variation of this circuit was found in cheap helium neon lasers in the 70's.
So you'll have a proper schematic by the end of the day along with a BOM, and then the group buy can start tomorrow, right? 😉
Hmm… An interesting thread that I never saw.
Not much in that box. They charge 150 bucks? There’s probably less than $10 worth of parts in there.
I’m kind of busy this time of year so I’m not going to be able to do anything right now. This looks pretty easy once the coil is chosen.
phenagan wrote:AH! Hadn't seen the old thread. Looking @ the photos & then the video on the website linked, it's not hard to guess how this is put together & works. The unit consists of two sections - the first just sends normal 110v through the string when the box is on. When the test button is pressed, the 110v is cut off and the second part of the unit is energized, which consists of a charge circuit pulsing a spark coil (probably a motorcycle one). This kicks a low current, high voltage (30KV) pulse across the string. This either fires the shunt in the bad bulb (same way a lightsaver goes, except that uses a piezo crystal to generate the spark) or if that fails, the spark jumps at the loose connection, creating the buzzing sound.The discrete components shown in the photos are a triac, a resister, a diode, a capacitor (probably a motor cap) and an unknown one (the green item), which may be a MOV acting as a snubber to protect the triac. The triac is being triggered the AC cycle to dump the charge in the big cap across the coil, creating the spark. By doing it this way rather than just drive the coil via a 12v transformer, the spark duration is shorter, so the chances of killing a good bulb is reduced.
A variation of this circuit was found in cheap helium neon lasers in the 70's.
sounds like you know what your doing any chance your willing to run with this after the season???
