First Year
 
Notifications
Clear all

First Year

10 Posts
6 Users
0 Reactions
7,042 Views
Posts: 14
Topic starter
(@samami)
Eminent Member
Joined: 8 years ago
[#50480]

Aloha,
Yes, it's another first year noob looking for help. I promise I have read A LOT. I just kind of wanted to make sure my concepts are correct before I buy $500 worth of stuff (I'm starting small).
I have a house with a detached garage, I'm hoping to light both as well as a "mega" tree (It's only 8 ft) that is near the garage
I'm purchasing from diyledexpress.com and pixelcontroller.com

  • For my 56' main roofline I'm doing 2 50 pixel sets of Pixabulbs 8" spacing 12V
  • For my 16' garage roofline I'm doing 1 25 pixel set at 8" spacing 12V
  • For my megatree I'm doing a spool of 250 pixels and will likely have to power inject at the two ends plus somewhere in the middle
  • One 12V 360W PSU
  • I'm getting a falcon 16v3 to run everything
  • I might get a Rasberry Pi

1) Please help with my power supply math, do I have enough juice.
2) Can I even use a single power supply when I have to power different things 20 ft away from each other
3) Do I need an expansion board and receiver if the falcon is in my house (20 ft away)...I guess how far away can I run a pixel string (or power for that matter)
4) How the heck does FPP work? Like is the workflow, set everything up on Vixen3 > Download to FPP > Connect to Falcon with ethernet???
4a) Does FPP run music too?
5) If I don't use FPP, then is it just Vixen3 > Connect Falcon to my computer with ethernet?
6) Do people use Boscoyo strips for mega trees or just let lights dangle.

Thanks for your help. I'll try to be a good citizen.
Mahalo,
Sam

PS Yes I live in Hawaii, don't be jealous it's really expensive to ship everything.


9 Replies
Posts: 299
(@dcamron)
Reputable Member
Joined: 10 years ago

1) You need 19.5 amps for 325 lights. The power supply you’ll get is rated at 29 amps so at 100% brightness you’re still good.
2) Yes. Try to keep your power runs as short as possible. Pixel data can go 20 feet from the controller to the pixel string without any problem.
3) Not required but you could if you want.
4) I used xlights but plan to spend some time with Vixen this year so not sure about Vixen workflow. The general flow is to setup a display in your sequencer, create a sequence and then upload it to FPP. Your controller will be attached to the FPP player via Ethernet. That can be a point to point connection with a single cable if that’s all you need.
4a) Yes. You’ll need an FM transmitter if you want people to listen in their car. A set of speakers if you want to make noise in the yard.
5) Yes. Your controller connects to the show player, whether the player is FPP or Vixen. The player can be on a PC, Raspberry Pi, etc.
6) Would highly recommend.

Make sure you order all the cables you need to get from point A to point B. You need somewhere to mount the controller and pigtails to connect to extension cables. Do some googling on falcon controller enclosures and look through the images.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

to expand on the answers above.

You can run your show from FPP, or from Vixen or xLights itself. The biggest advantage to FPP is having a dedicated, purpose built device to run your show for 6 weeks. You don't need to tie up a regular computer for all that time. Nor do you have to worry about any of the headaches of a general purpose computer (heat, fans, viruses, automatic updates, other software compatibility, etc...) Technically speaking, the FPP runs on a raspberry pi, which is technically a computer. But it's a very specialized one with no fans, makes minimal heat, runs an operating system that's been optimized for the purpose, and only runs purpose built software to drive the show. Best of all, it's cheap!

Yes the Pi plays audio. It has an onboard 3.5mm TRS connector for audio output. However the onboard audio doesn't sound that good. Many people get better sound by connecting an external USB sound card like the soundblaster play 3.

Pixels should not be strung unsupported. if you do, you're going to find a lot of bad pixels in a fairly short time. Boscoyo strips are one answer to that problem. All of the support is borne by the strip holding the node itself. the wires are under no tension and minimal flex. But there's other ways as well. You can zip tie the nodes to PVC pipe, tape it to strapping material, wrap it around rope or cord. All depends on the look you're going for.


Reply
Posts: 401
(@kensington)
Reputable Member
Joined: 11 years ago

And to throw more at you, you could forego the F16v3 the first year and run the whole thing off a Falcon PiCap, which essentially combines the FPP and a pixel controller.

The FPP is a great system and the developers are constantly improving it. It’s well-worth the trouble of getting a Raspberry Pi and loading it up.


Reply
Posts: 299
(@dcamron)
Reputable Member
Joined: 10 years ago
Kensington wrote:And to throw more at you, you could forego the F16v3 the first year and run the whole thing off a Falcon PiCap, which essentially combines the FPP and a pixel controller.

The FPP is a great system and the developers are constantly improving it. It’s well-worth the trouble of getting a Raspberry Pi and loading it up.

Very true. You don't need to spend a couple hundred for a controller to run that many pixels. I also have to mention this controller since it's such a great option. It's incredibly fast, simple and cheap.


Reply
Page 1 / 2
Share: