First time set up
 
Notifications
Clear all

First time set up

4 Posts
3 Users
0 Reactions
1,655 Views
Posts: 5
Topic starter
(@reidsim)
Active Member
Joined: 17 years ago
[#39102]

This is my first time. I have read most of it but still not sure what I need to get. I would like to have 48 channels for this year. I am not sure what kind of controller do I need but I would like to run three Renard SS16. Who sell them? Someone mention Wayne J sell group kits. I have lot of Cat5 cables and was hope I can use it and less extension cord. Also what kind FM transmitter should we get? I just want simple for this years. I am good with electronic and handy man. But I don't know what kind of equipment that I can run music Christmas lights. I have some regular christmas light and some are LED. Can we use it mixed or must all LED light? I am not concern on RGB lights at this time. Maybe next year. I will use C7 on top of roof and some small old light and new LED light on big trees. I hope we can mixed regular and LED light to run it. I am open to run it.


3 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

You've been a member since 2009 and this is your first time? What the heck have you been waiting for?! lol...

Yes - Wayne would be your best bet for getting some RenSS16's - he normally has them boxed and ready to go - assuming he has some in stock and is not too busy at this time - send him a PM.

You must NOT use Cat5 cables to run 120vac - it's not meant to carry that much voltage for both the wire gauge (only 24 or 26#) and thin insulation. You can use the Cat5 as communications between your RenSS controllers but not for AC voltage. Most folks either go one of two routes - either buy the cheapo 6/9/15' extension cords (sometimes $1/each on sale) and cut the plugs off - OR - get a long spool of SPT1/2 wire and the correct 'vampire' plugs to make your own cords. The advantage to the spool is you can make them as long/short as you need to reach your particular lights. If you have a lot of stuff in one place, then it doesn't matter so much.

As for FM transmitters, there are several - I prefer EDM but they are pricey (but excellent) or there are some Czech made units on eBay that seem to work or some folks use the VAST USB model that plugs into your PC.

You are starting quite late for this - most folks will be starting up their shows in the next week or two and you still have sequencing to do of the songs. There are several free sequence sites around - but you will need to modify them a bit to match your specific setup.


Reply
Posts: 5
Topic starter
(@reidsim)
Active Member
Joined: 17 years ago

Budude

Thank you for information. I didn't realized that I was member since 2009. I wasn't ready at that time. Now recently my son would like to have one for this year. I know it is kind of late but I will try my best. I will NOT use Cat5 as power cord. I was plan to put SSR16 in tree and use one long cat5 and one long power extension cord from garage where computer is to SSR16. Do you keep all SSR and computer or controller in the garage and use many extension cord to different places where the lights are? What kind of controller do you use? Ardunio or Raspberry PI?


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

There are a few trains of thought here. You can have the controller in the garage and miles of extension cords to each item. But most have the controllers in the yard closer to the items. The cat5 communication cable goes from the pc to controller and daisy chains to the next controller and so on. There is also controllers without on board SSRs, and the separate SSR boards at the item. But I would not recommend that to start. Get with Wayne and get your kits built. I'm sure you will have more questions then. In the mean time you should look at software to run your show. Vixen 2.1 or 3, Xlights, HLS are some to look at. You can download, setup, and start using them before your controllers get here.


Reply
Share: