aixelsyd wrote:Also could/will the Simple Renard 32's have a problem with this too? My cable runs for those are very short (15' at most). I plan on using more of those next year so I need to plan.
I haven't seen any yet with the SR 32's, I will know more once I start my show but I am at a location were it rarely gets below freezing.
It's 18F here in the Twin Cities, headed down to 12F tonite. The DirkCheap is working just fine so I don't really think there's going to be much of an issue with it. The VO2223A chip is spec'ed down to -40 so I'm not anticipating any issues with respect to temperature.
dirknerkle wrote:It's 18F here in the Twin Cities, headed down to 12F tonite. The DirkCheap is working just fine so I don't really think there's going to be much of an issue with it. The VO2223A chip is spec'ed down to -40 so I'm not anticipating any issues with respect to temperature.
Brrrr That's Cold 😯
Well.. it's not good....
As they are.. I have issues... when the load on the board goes up the dirkssr's start to dim... some channels do not even light on the same ssr. My opinion.. If I were anyone... and had these issues... I would find a way to fix before using... I will do some changes to the sequencing to see if I can drop the load with out changing parts...
KY- I'm currently using a few of your sequences.. and the result is very noticeable.. my 24 channels are 25ft from controller...
The most noticeable area is where the candy canes are side by side on different ssr's... one side is definitely brighter then the other side.. Half tempted to find the parts to build a Regular SSR for that side as well...
Going to change the intensity of different areas on that board... will update if any better
dirknerkle wrote: I think that perhaps one key is having a power supply that's got enough headroom to ensure that there's ample current to drive all the electronics.
So in my case I'm using the power supply from the buys... would you suggest something different for better results?
Can you measure the voltage on the controller when "the load on the board goes up"? If the power supply is suspect (as your post implies) you should really isolate, identify and solve this problem first. What is the distance between the power supply and the controller, and what gauge wire are you using for bringing power from the supply to the controller?
The supply is about 8 inches from the board, the wire is stranded 14gauge from the supply to the Board
Is power supply really my issue since I have 2 other Ren64's fully loaded using SSR's with the MOC3023 that work flawlessly, then I have this board... I can test tomorrow.
I really don't think my post implies that the power supply is my issue, I think my supply is now good, and so is my board... I think my issues are leading up (or lack there of) power supplied to my board during a sequence... in other words the amount Dirks are not working with my Ren64, because of current issues... but if it was loaded with A/C SSR's this board would react just as the rest of my 128 channels.
Has anybody tested these Dirk Cheap SSRs using non PWM firmware? If the VO2223A will reliably latch and not cause a flicker problem switching to non PWM could help to get the current needed from the transformer down.
tstraub wrote:Has anybody tested these Dirk Cheap SSRs using non PWM firmware? If the VO2223A will reliably latch and not cause a flicker problem switching to non PWM could help to get the current needed from the transformer down.
So far, I think Dave is the only one having trouble. I'm hoping to be able to test on Sunday. Of course, I'm hoping for no troubles.
After the test show ended today.. I tested some more.. so was it really over??? lol
I only tried this on one song and had very positive results... I picked the song that had the most issues. The only issue I could see afterwards is intermittent flicker instead of being extremely dim or not on at all..
I selected the entire sequence, "find and replace" and changed every cell that was 99 and 100 to 98.
This showed very positive results.. I can deal with a flicker here and there... I have changed all of my songs to this and will run the show tomorrow to see how it goes.
Anyone know if I'm at 98 for max intensity what the next drop would be to lessen the load?? That is without making fades to difficult fix... don't want to totally screw things up... so for those of you running with no issues... what are you using for max intensity on your sequences?
In all reality I would have only needed to do this on that board.. but figured why not do it to all.. Will know more tomorrow
