Snowflake Build
 
Notifications
Clear all

Snowflake Build

9 Posts
5 Users
0 Reactions
3,034 Views
Johnfish211
Posts: 404
Topic starter
(@johnfish211)
Reputable Member
Joined: 14 years ago
[#30895]

Hi all,

If you remember last year I made snowflakes out of dollar tree plastic snowflakes and 2811 pixels strips. You can see my attempt on the other site here. http://diychristmas.org/vb1/showthre...eepo-Snowflake It was my first attempt and I learned a lot about water infiltration and how brittle plastic becomes in the cold. The 5 snowflakes I built made it through my show but not without reworking the pixels and adding splints to the dollar tree snowflakes as both failed. This year I am taking a different approach.

1. I am going to mount the snowflakes under the eaves out of the direct effects of the weather. I know this is not guarantee but it should mitigate direct infiltration.

2. I am removing the pixels from the silicone tubing and placing them in 1/2 inch clear heat shrink. (I found a dealer on ebay that was selling 100 ft of it for 18 dollars.) I have tested them full on white for several hours inside a sealed piece and found no heat issues. I am only sealing up to 6 pixels per section of heat shrink. It seems to work really well. At the wire end I am shrinking progressively smaller pieces of heat shrink to semi seal the ends (I know this isn't 100 % and am still investigating the best way to completely seal them. I may do nothing else and see how it works)

3. I am adding 12 more pixels to the snowflake to give it more of a snowflake and less of a star feel.

4. I am making each section independent so they can be removed and worked on. There will be 6 sections with 6 pixels and 6 sections with 2 pixels.

5. I have made a coroplast back plate to mount the pixels. I am using Velcro to hold the pixels in place so I can position them properly and so they are easy to remove for repair. The wires are all hidden behind the coroplast. I will be adding some small PVC pipe on the back to give it some rigidity and for mounting to the house.

6. The snowflake will be held over the pixels using a few strategically placed tie wraps.

7 I will be using Kombys to control these guys. Probably 3 snowflakes per Komby with a total of 6 snowflakes. I have already created a prototype and used nutcracker to test some affects. It worked great but I still need to figure out the best wiring to match a nutcracker model or define a custom model for nutcracker (this is still new to me and I don't know if it will even work).

Here are a couple pictures of what I have so far. First one is of the pixels strips velcroed to the coroplast. The second is with the snow flake laying on top.

IMG 20140323 192756 155
IMG 20140323 192835 608

8 Replies
Posts: 30
(@inspector-steve)
Eminent Member
Joined: 15 years ago
Johnfish211 wrote:
2. I am removing the pixels from the silicone tubing and placing them in 1/2 inch clear heat shrink. (I found a dealer on ebay that was selling 100 ft of it for 18 dollars.) I have tested them full on white for several hours inside a sealed piece and found no heat issues. I am only sealing up to 6 pixels per section of heat shrink. It seems to work really well. At the wire end I am shrinking progressively smaller pieces of heat shrink to semi seal the ends (I know this isn't 100 % and am still investigating the best way to completely seal them. I may do nothing else and see how it works)

.

I will just share that last year when I was working with my strips, I just shot a dab of silicon sealant on both sides of the ribbon near my solder work before I slid the shrink tube over my connections. The one big size shrink tub sealed just fine with silicon inside.

Steve


Reply
Posts: 115
(@loveroflife96)
Estimable Member
Joined: 16 years ago

Interested in this idea. Seems like an inexpensive way to get some good snowflakes. Do you have any video of these in use from last year?

Duane


Reply
rfallatt
Posts: 648
(@rfallatt)
Honorable Member
Joined: 16 years ago

Very interested in seeing these working...


Reply
Johnfish211
Posts: 404
Topic starter
(@johnfish211)
Reputable Member
Joined: 14 years ago

I hope to have a video by the weekend. I still have to finish up a couple of the strips and wire them. Life has gotten in the way of completing it. I will post when I have made some progress.

John


Reply
Johnfish211
Posts: 404
Topic starter
(@johnfish211)
Reputable Member
Joined: 14 years ago
loveroflife96 wrote:Interested in this idea. Seems like an inexpensive way to get some good snowflakes. Do you have any video of these in use from last year?

Duane

Here is the link to my videos from last season (2013). The snowflakes are on the right side of the display. There is a group of 5 of them. My wife did the sequencing and these are her first attempt. I think she did a great job!

http://doityourselfchristmas.com/forums/showthread.php?31029-The-2013-Earle-Family-Christmas-Display-Videos

John


Reply
Johnfish211
Posts: 404
Topic starter
(@johnfish211)
Reputable Member
Joined: 14 years ago

Here is a quick update on my build. No new hardware but I have created a model in nutcracker with the help of Keebler's custom model spread sheet (see this thread http://doityourselfchristmas.com/forums/showthread.php?27747-Great-new-excel-spreadsheet-to-help-build-custom-models&highlight=nutcracker+snowflake ). I am really pleased with how it came out and the nutcracker effects look great. Building the model was invaluable in helping me determine how to wire the strips together. Hopefully I will have a working prototype this weekend. I will update when I have some video to show everyone.

John


Reply
Johnfish211
Posts: 404
Topic starter
(@johnfish211)
Reputable Member
Joined: 14 years ago

Well I completed one snowflake. It is a significant improvement over last years attempt. Here are a couple stills and a link to a video of it doing the butterfly effect from nutcracker.

IMG 20140329 095837 273
IMG 20140329 204304 637
IMG 20140329 204358 992

Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

Nice!


Reply
Share: