EDM Buzzing
 
Notifications
Clear all

EDM Buzzing

28 Posts
7 Users
0 Reactions
10.7 K Views
Posts: 259
(@cmschleich)
Reputable Member
Joined: 11 years ago
Cmschleich wrote:Yamaha MG10XU. My research spun out of control. That's where I ended with the USB + quality curves. If you get something cheap and it works let me know. I have 45 days to return.

IMG 8432

Sent from my iPhone using Tapatalk

And I killed my minivan in the process. Apparently these boats draw more power with the engine off than the typical sedan.

Big ferrite bead (snap on that comes with a TV) on the radio power helped a bit, but I've had that on since the beginning of the thread. Small beads from RadioShack were useless.

Sent from my iPhone using Tapatalk


Reply
Posts: 215
Topic starter
(@reelpilot)
Reputable Member
Joined: 12 years ago

Here's an update to my buzzing and unfortunately I'm worse off than I was before. I received my EDM back this week and started doing more testing with it. Using the exact same setup as all my previous tests, which is stock with the rubber duck antenna, I am now receiving significant static on my radio in addition to the buzzing. I've also tried multiple frequencies with no change. The static is so loud and annoying that I can barely make out the buzzing and the music sounds terrible as a result. An email to EDM yielded the response essentially saying that it tested fine when they had it. I have since tried ferrite beads, running 25' of coax to get the antenna away from the EDM and adding a mixer ahead of the EDM's input. The results of all of those were negligible at best leaving me with the same loud static and underlining buzzing. I can't even use it at this point because it sounds so terrible. I have no idea why I have a major static problem now when there was none before. The box looked to be in good condition and had no signs that it was dropped. I would be interested if someone else in the Denver area had an EDM to do a side by side comparison, but in all likelihood I'll review those other threads on good transmitters and look to buy something else.


Reply
stallionent
Posts: 1460
(@stallionent)
Noble Member
Joined: 13 years ago

Ouote below is from here: http://www.jpole-antenna.com/2013/10/11/broadcast-high-quality-music-for-your-holiday-lights-display/

Naturally our inclination is to position the transmitter close to the computer feeding the audio signal to it, but remember your highest quality signal will be achieved by putting the antenna outside and keeping your feedline run short. A better option is to keep the transmitter close to the antenna and run a longer audio cable from the computer to the transmitter.

Reply
Posts: 215
Topic starter
(@reelpilot)
Reputable Member
Joined: 12 years ago

That sounds logical, but in my testing I was trying a longer run from the EDM to the antenna with high quality coax at the direction of EDM who told me that my buzzing was likely the signal radiating back to the EDM itself. They said that moving the antenna further away from the EDM has helped reduce that problem for them in the past. In my case clearly that hasn't worked. I have virtually identical crappy reception whether I use the antenna directly out of the EDM or 25' away. I just can't figure out why I have a static problem now when the audio was very clear before other than the background buzzing.


Reply
T.D.Sutton
Posts: 445
(@t-d-sutton)
Honorable Member
Joined: 17 years ago
reelpilot wrote:Here's an update to my buzzing and unfortunately I'm worse off than I was before. I received my EDM back this week and started doing more testing with it. Using the exact same setup as all my previous tests, which is stock with the rubber duck antenna, I am now receiving significant static on my radio in addition to the buzzing. I've also tried multiple frequencies with no change. The static is so loud and annoying that I can barely make out the buzzing and the music sounds terrible as a result. An email to EDM yielded the response essentially saying that it tested fine when they had it. I have since tried ferrite beads, running 25' of coax to get the antenna away from the EDM and adding a mixer ahead of the EDM's input. The results of all of those were negligible at best leaving me with the same loud static and underlining buzzing. I can't even use it at this point because it sounds so terrible. I have no idea why I have a major static problem now when there was none before. The box looked to be in good condition and had no signs that it was dropped. I would be interested if someone else in the Denver area had an EDM to do a side by side comparison, but in all likelihood I'll review those other threads on good transmitters and look to buy something else.

Hi, Are you sure of the input level/volume going into the transmitter from your audio source, because your description sounds very much like a signal/noise problem. Have you confirmed the volume setting of your receiver on a local FM station compared to a local FM station, beware of the volume on heavy rock stations because they compress/process their audio pre-transmitter something awful and consequently sound very much louder than they should be.

Once you have "calibrated your ears" to the FM stations volume, then change the receivers frequency to your transmitter, with music playing, and see how loud it is, if it is very quiet, increase the volume of the audio signal from your music source into the transmitter until it matches the volume that you "calibrated your ears to" and see if the background noise appears to go away. If it is still as noisy as you suggest, I am out of my depth, sorry 🙁

You are correct in placing the transmitter antenna well away for the transmitter because it can, on occasions, get back into the transmitter via the audio input cable and effectively create a version of feedback, very nasty and awkward to fault-find/cure.

Just a couple of thoughts for you.

Terry


Reply
Page 5 / 6
Share: