I made some floodlight stands for my 10w RobG floods. This is my 10w floods mounted on the prototypes:

It can be adjusted to sit high or very low profile depending on your needs. I painted mine black so they disappear at night (the photo above is obviously before I painted, figured they would show better as white).
To make it you will need to print one of these caps (or find another way to attach the floodlight to PVC):
http://www.thingiverse.com/thing:1823950
Inventory (per stand):
3 - 6" sections of 1/2" pvc pipe
5 - 1-1/2" sections of 1/2" pvc pipe
4 - 1/2" Elbows
1 - 1/2" Cross
1 - #6 x 5/8" construction screw (or any other sheet metal type screw in your drawer)
1 - 1/4-20 x 1" hex head bolt
2 - 1-1/2" 1/4" flat washers. The printed plate will accept up to 2-1/2" washers.
1 - 1/4-20 wingnut
1 - 1/2" 45 Elbow (OPTIONAL and another 1-1/2" section of pipe)
Do NOT glue any joints.
Use the photo for easy assembly of the pipe.
Insert the hex bolt into the end of the printed piece and line it up with the hex receptical. Use a washer and wing nut to pull it into the recess.
Drill a 7/64" hole on the flat I provided on the printed piece. Insert one 1-1/2" coupling PVC pipe section and screw in the screw so its snug. This will prevent rotation of the head on the PVC. Insert the assembly into the top of the cross. See photo below:

Attach the floodlight by placing one washer on the bolt with the stamped side up (yes, washers have a top and bottom side, you want the smooth side up). Place the light's bracket on the bolt, follow with the next washer, this time stamped side down. Spin on the wingnut and tighten snugly. The smooth sides of the washers should be against the light bracket which will prevent chewing into the paint.
Adjust the legs as needed for your installation. Enjoy the quick setup. If you spread the legs really now, you may have issues aiming the floodlight. In that case remove it from the cross. Insert the optional coupler PVC and the optional 45 Elbo. Insert the flood base into the 45. That should bend the head up enough to aim it whereever you need.
When packing them away, these will fold flat for easy storage or you can remove the legs and it stores even smaller.
If you are making these for larger floodlights, I recommend you increase the leg length to 12" instead of only 6".
A "poor man's cap" would be just that... A PVC plug with a hole drilled through it.
It wouldn't be as nice as these, but if you don't have a 3D printer...
Yea, suppose a cap would work. You would have to sand the end to get a flat on it. And you would need another nut to hold the bolt to the cap, otherwise turning the wingnut would just spin the bolt in the cap.
For those of us without a printer, a plug would also work. A cap goes on the outside of the pipe. A plug goes inside an open spigot hole. Plugs are typically pretty thick plastic and take threads nicely. You could drill a hole in the plug and tap it for the bolt and screw the bolt from the inside out. There's your stud for the flood yoke.
Now that you made me think that up, I may just do that for mine. I don't need the whole stand setup though. All of mine will go on grass or garden. I'll just use a straight piece of pipe and stick it in the ground.
Sent from my iPhone using Tapatalk Pro
I just did my floods today, screwed them to a 16" 2x4 that lays flat and gets staked to the ground
The reason I made mine this way is so they can be moved around. I am putting them close the the house facing up for a harsh spooky look. At Christmas I want to pull them back a few feet to soften the shadows and make them less sinister looking.
You being a lighting guy should know about uplighting. For those who don't, when you use an up-facing look it inherently has an evil look to it. If you look in movies and photos that have an evil or sinister feel to them, look at the lighting, its likely coming from the bottom up at the scene or characters. This deepens the facial features and casts unusual shadows.
Two photos of the same kid. One has a darker feel to it, one lighter. Its the lighting angle.


Here is a photo of a crypt entrance I took down in Peoria. I placed my strobes low so they would enhance the shadows and texture.

So, I wanted mobile floods. Thus, mobile stands. And I can pick them up at the first nice day. I don't have to wait for the ground to thaw to get rebar out of the ground.
Here is a perfect example. In Star Trek TOS, episode Enemy Within, Kirk is split into good and evil halves by a transporter accident. When they showed the good Kirk, they used soft overhead lighting:

The same actor when playing his evil self was lit with uplights to portrayan evil look to him:

