Cutting lights ques...
 
Notifications
Clear all

Cutting lights question

16 Posts
10 Users
0 Reactions
6,447 Views
Posts: 2216
Topic starter
(@ctmal)
Famed Member
Joined: 19 years ago
[#11957]

Over the last couple of years I've cut many 100 count strings into 50 count strings. As a result I have tons of 50 count string with no male connectors. I don't want to use vampire plugs on these because they don't have fuses. I also have a coffee can full of unused fuses but I haven't been able to find any fuse holders for that size fuse(and I'd have to see if the cost would justify it).

Anybody have any solutions other than waiting for strings to go bad so I can cut the fused plug off?


15 Replies
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

IMO, the fuses are only needed if you are going to go string to string with a bunch of set to prevent overload the wire. I did the same thing for some snowflakes I'm building. I simply used the plugs that I cut off the extension cords used for my controller output. I had over 200 of them.


Reply
Posts: 1424
(@oldcqr)
Noble Member
Joined: 18 years ago
ctmal wrote:Over the last couple of years I've cut many 100 count strings into 50 count strings. As a result I have tons of 50 count string with no male connectors. I don't want to use vampire plugs on these because they don't have fuses. I also have a coffee can full of unused fuses but I haven't been able to find any fuse holders for that size fuse(and I'd have to see if the cost would justify it).

Anybody have any solutions other than waiting for strings to go bad so I can cut the fused plug off?

Cut the fused plugs off bad sets, natually :mrgreen::cool:. You should have equal numbers of sets that are missing either a socket or a plug.

I do the same thing quite a bit (make 50's out of 100's). Once you have enough plugs/sockets to go around, I end up reusing them. I have some ends that have been cut and spliced onto other sets 3 or more times.

Unfortunately unless you have scraps laying about (like kyc), there is no cheap solution. You can 'mortgage your future' by cutting the ends of new strings and then holding onto those strings until the originals go bad (when you can re-harvest the ends). You'll need 1/2 as many boxes of lights as you have sets that need ends.


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

You are welcome to a 100 of my plugs for the price of shipping. Slow ground for those couldn't be more than $5-6 from NKY to Cincy. Of course, I have to find them in the storage room. For that, I need to put a rescue team on stand-by in case I don't emerge. Of course, always willing to try for a fellow DIYC'r

I'll even forget that fact that your probably a Steelers Fan 🙂


Reply
Posts: 2216
Topic starter
(@ctmal)
Famed Member
Joined: 19 years ago
kychristmas wrote:You are welcome to a 100 of my plugs for the price of shipping. Slow ground for those couldn't be more than $5-6 from NKY to Cincy. Of course, I have to find them in the storage room. For that, I need to put a rescue team on stand-by in case I don't emerge. Of course, always willing to try for a fellow DIYC'r

I'll even forget that fact that your probably a Steelers Fan 🙂

Thanks for the offer but I do have plugs without fuses. I'd just like to find a way to have them fused. 2 years ago we had a c7 socket go bad. It had scorch marks inside the socket and between the fuses inside the controllers and the fuse in the string itself saved us from a house fire. That's why I get nervous running lights without the fuses.

And I'm an Eagles fan:-D


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

If you are that paranoid (understandably so) then I'm surprised you use any modified light strands. For a fifty light strand and not much chance of blowing, then i would simply solder the fuse in-line and add the plugs you have.

Fortunately, none of my display is mounted to my house so there's little chance of it catching anything on fire.


Reply
Pwmcguire
Posts: 575
(@pwmcguire)
Honorable Member
Joined: 18 years ago

Every thing I modify I put fused plugs in . So when I cut 100's into 50's
I find another fused plug, I picked a bunch of strings up at a garage sale for
5 dollars. I dont care if they work, I want the plug. In fact, I need some now. I will probably hit some garage sales Saturday, check Craigs List. That's what I'm doing


Reply
Posts: 406
(@jboyles7)
Honorable Member
Joined: 17 years ago

Does this help?

http://www.littelfuse.com/products/Technology/Fuses/search.html

I think they are 3 amp. Solder it in-line then heat shrink.

I've been looking for clips for an SSR design that uses those extra plug fuses. I'll let you know if I find it.


Reply
james70818
Posts: 2045
(@james70818)
Noble Member
Joined: 19 years ago

When I started making my mini trees, I needed 200 and 300ct strings of mini's. I cut off the female end of the fist string and both ends of the next strings. I solder them together and us the 1/8" Adhesive lined heat shrink to seal everything off. I have been racking up a lot of ends this way. It is also amaizing how fast you can use up heat shrink 1 inch at a time!


Reply
Posts: 304
(@dennis-cherry)
Reputable Member
Joined: 19 years ago

You should have at least 1 fuse on the first string of lights rated at 3 amps.


Reply
Page 1 / 2
Share: