Technicolor Pixels ...
 
Notifications
Clear all

Technicolor Pixels ARE NOT FIXED

251 Posts
31 Users
0 Reactions
70.1 K Views
bcwhitehead
Posts: 119
Topic starter
(@bcwhitehead)
Estimable Member
Joined: 15 years ago

I have done that with butt connectors also. LOL


Reply
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago
txag2008 wrote:When you replace these nodes are you making 6 different soldered connections and then heat shrinking? Just curious since it seems like a lot of work (although I really don't think there's any better way...)

You really want to use a watertight seal on your joints. The water will wick up inside the stranded wiring into the pixel very easily. Many of us managed to buy some professional RGB LED floods (TIR Floods) because they were installed wrong and the water wicked in the power leads and eventually shorted them out. Eventually the water leaves deposits that will short out the connections internally. Use a good adhesive lined heat shrink tube on all of your splices, including any pigtails you add to a string.


Reply
Posts: 9
(@djohnson7)
Active Member
Joined: 12 years ago

So I had two strand failures after the last rainfall. At least in my case it was the Technicolors that i had mounted with the bulbs pointed up. Most of mine are mounted with the bulbs pointed out (horizontally) and are still doing fine. I would be interested in hearing how the other Technicolor lights that are failing are mounted.


Reply
Posts: 191
(@buddhawood)
Estimable Member
Joined: 16 years ago

I only had 200 pcs last year for my Merry Christmas sign Ray replaced them but I didnt use them because I was afraid it would happen again. I left a full strand of Seasonal Entertianment Rainbow pixels on the gutter since last season since it was in a terrible location and were not very noticable. They are working perfectly again this season...just a little yellowing but you cant tell the differnce between them and the ones properly stored.


Reply
bcwhitehead
Posts: 119
Topic starter
(@bcwhitehead)
Estimable Member
Joined: 15 years ago

Hey all just wanted to share a test I did with a test pixel one that hasn't been out in the weather yet. I sealed it with some of that rustoleum never wet. Just the first layer of it. After it dried for a couple hours I soaked it in some water for a few hours with no issues. Then Froze it in a container an once it was frozen let it sit out running through a cycle until it was full de-thawed. And it was still working fine. Just some tests I ran. I am trying to keep up on fixing my. not to worried about the stuck pixels as much as the ones all white. Once I fix and tested them I am gonna try the flex seal that comes in clear. Gonna give that a try it is few dollars cheaper.


Reply
moondew
Posts: 53
(@moondew)
Trusted Member
Joined: 13 years ago

I tried some silicone seal but it just peals off. How well does the rustoleum adhere to the pixel plastic and the wire insulation?


Reply
bcwhitehead
Posts: 119
Topic starter
(@bcwhitehead)
Estimable Member
Joined: 15 years ago

I went away from the never rustolem due to cost and I was only using the first can due to the other leaving the whole string frosted white. I using flex seal in clear. It seems to be adhering well.


Reply
moondew
Posts: 53
(@moondew)
Trusted Member
Joined: 13 years ago

Did you try the Loctite 406?


Reply
tucsonlights
Posts: 667
(@tucsonlights)
Honorable Member
Joined: 15 years ago

I think plastidip is the same thing as neverwet. I dipped some of my ink1003 pixels in it and it pretty much sealed everything. I haven't soaked them in water but the bond is strong. Another thought is quick drying hot glue. You can inject it into the problem points and it will seal it.


Reply
moondew
Posts: 53
(@moondew)
Trusted Member
Joined: 13 years ago

I tried the Loctite 406 on a single pixel to see how it looks and bonds.

It takes barely a drop of Loctite. It almost looks like the plastic and the wire insulation become one. I didn't put any around the LED, just the wires.

Tonight I will apply it to a full string.


Reply
Page 8 / 26
Share: