Some E682 questions
 
Notifications
Clear all

Some E682 questions

20 Posts
11 Users
0 Reactions
6,281 Views
Steven010
Posts: 416
(@steven010)
Honorable Member
Joined: 18 years ago

Technically you can control 6 dmx universes with the e682. However there are a few caveats. First of all only 510 channels per universe are supported. (Leaving 2 unused, because one pixel cannot span across two universes) so that's 170pixels per universe for a total of 1020 pixels.
Then your strings have to be divided appropriately across the 4 outputs in each of the 4 clusters. If all of your strings are the same and you loaded all 16 outputs with strings of 63 pixels in length, you'd end up having 1008 total. (With 12 wasted because 16 doesn't divide evenly into 1020). You could have 12 strings of 64 and 4 of 63 and use all available 1020. This is all related to addressing and configuration, these are theoretical limits and situations.
Keep in mind strings over 50 can have voltage drop problems. So there's other electrical considerations you'll need to work out.
If you need more pixels, just add another controller and keep going. The average cheap consumer home network can handle somewhere around 20 universes of network traffic. (Thats 3.3 fully loaded e682s) This network limit isn't a firm number because there's a lot of other variables that come into play. When you get somewhere beyond that limit, you need to start doing some network engineering and perhaps use commercial grade network equipment to make it all work well.
Hope that's a start for you. Welcome to the hobby!

OK, I am worried now...are you saying the max number of pixels I can have is ~3366 with Vixen? I was hoping for 20k-ish+ 800 channels of Renard serial....


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
Steven010 wrote:Technically you can control 6 dmx universes with the e682. However there are a few caveats. First of all only 510 channels per universe are supported. (Leaving 2 unused, because one pixel cannot span across two universes) so that's 170pixels per universe for a total of 1020 pixels.
Then your strings have to be divided appropriately across the 4 outputs in each of the 4 clusters. If all of your strings are the same and you loaded all 16 outputs with strings of 63 pixels in length, you'd end up having 1008 total. (With 12 wasted because 16 doesn't divide evenly into 1020). You could have 12 strings of 64 and 4 of 63 and use all available 1020. This is all related to addressing and configuration, these are theoretical limits and situations.
Keep in mind strings over 50 can have voltage drop problems. So there's other electrical considerations you'll need to work out.
If you need more pixels, just add another controller and keep going. The average cheap consumer home network can handle somewhere around 20 universes of network traffic. (Thats 3.3 fully loaded e682s) This network limit isn't a firm number because there's a lot of other variables that come into play. When you get somewhere beyond that limit, you need to start doing some network engineering and perhaps use commercial grade network equipment to make it all work well.
Hope that's a start for you. Welcome to the hobby!

OK, I am worried now...are you saying the max number of pixels I can have is ~3366 with Vixen? I was hoping for 20k-ish+ 800 channels of Renard serial....

It's not a "Vixen" limit. E1.31 is ethernet and the limitation is on typical Home Network bandwidth. There are certainly ways to change that. So are you planning on upgrading to 20K Pixels immediately? No matter what Software you choose, you will have a great deal of work in front of you. I know Joe Hinkle (HLS) made some improvments in load times and such, but I'm guessing that compiliing a show with 60K+ channels will take a great deal of time.

The truth is that you are talking Commercial numbers here and it's going to take some upgraded equipment to run. Better Networking gear, faster computer and endless hours of sequencing and show building.

Edit... I just went to your website. I only looked at the Cover Photo. I say go for it 🙂


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

In my opinion, it's as much a limit of how much computing power you have to output the commands as it is bandwidth to the controllers. I know that folks with 15-20,0000 pixels are seeing slowdowns, so you need to be sure you have enough horsepower to drive all those pixels.

Lots of folks will tell you to start small, since the sequencing of all those pixels will be as much an issue as building the megatree or mounting the lights...


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

I second that. It's not that it's not possible. But it's definately gonna require planning and research on your part. When I read your first post I just assumed you're a complete newbie expecting it to just work with DIY home grade stuff.
So long as you get a solid handle on the network and organize your bandwidth appropriately you'll be ok.
Word of caution, I don't think vixen 2.x is a good choice for pixels. You'll probably want to check out hls, lsp, or even a pro package like madrix. Vixen 3 is promising as well but its not ready for prime time yet. Madrix isn't a true sequencer. It's more of a pixel mapping sofrware. You can use it with any of the others like vixen or hls or lor and trigger madrix presets from just a few sequencer channels.

--Jon Chuchla--

Sent from my iPhone using Tapatalk


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
jchuchla wrote:I second that. It's not that it's not possible. But it's definately gonna require planning and research on your part. When I read your first post I just assumed you're a complete newbie expecting it to just work with DIY home grade stuff.
So long as you get a solid handle on the network and organize your bandwidth appropriately you'll be ok.
Word of caution, I don't think vixen 2.x is a good choice for pixels. You'll probably want to check out hls, lsp, or even a pro package like madrix. Vixen 3 is promising as well but its not ready for prime time yet. Madrix isn't a true sequencer. It's more of a pixel mapping sofrware. You can use it with any of the others like vixen or hls or lor and trigger madrix presets from just a few sequencer channels.

--Jon Chuchla--

Sent from my iPhone using Tapatalk

No, I think Steven Jumped in on another user's thread.


Reply
Page 3 / 4
Share: