San Device E682 Set...
 
Notifications
Clear all

San Device E682 Set up Problem

9 Posts
4 Users
0 Reactions
15.6 K Views
Posts: 14
Topic starter
(@ralph-a)
Eminent Member
Joined: 16 years ago
[#34041]

First year with E682. Running with LOR Advance. When testing my lights cluster three will not operate lights. Running 12vdc strips. When I first plug in the power to the E682 the lights will light up in all different colors, but only on cluster 3. Other cluster 1, 2, an and 4 are off at this point. Then all lights on cluster 3 turn off and all other clusters turn on to the appropriate color for the test pattern. All fuses ok.

To make sure it was not a strip problem I removed a strip from another cluster that was working properly and plugged it into a cluster 3 connection and it failed to work.

Any advice would be greatly appreciated!!

Thanks Ralph

Here is a screen capture of the E682 network page, https://onedrive.live.com/?cid=DA4CF1723ACD7017&id=DA4CF1723ACD7017!135


8 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I would suggest you configure universe 8-12 to some out of the way universe number - as-is they overlap - don't think that's your problem but it would eliminate the possibility. Put 8-12 at 1008-1012 or something. The way it is now is where you are having the problems but it may be a qwinky-dink...


Reply
Posts: 1792
(@barbotte)
Noble Member
Joined: 17 years ago

well you cluster 3 start at univers 10 and finish at universe 12 chanel 180 .. but u have cluster 4 starting universe 11 witch i think it is impossible as they will be overlapping the cluster 3 ...try to make cluster 4 starting at univers 12 chanel 181 or make it universe 13 chanel 1 either way the way they are they are conflicting ..then try a test patern again also are u sure you whant to run multicast and no unicast ??
cheer


Reply
Posts: 14
Topic starter
(@ralph-a)
Eminent Member
Joined: 16 years ago

Thank you Brian and barbotte! I will play with the universe settings and see it that changes anything. When the E682 is in test phase would the universe settings make any difference?


Reply
derekbackus
Posts: 565
(@derekbackus)
Honorable Member
Joined: 15 years ago

Probably not. Make sure the ICs are all seated properly with no stray pins that are not in the carrier. Also, take a look at the resistor arrays, maybe swap them out (unplug the poser first). I had a group today that wouldn't work. After an hour of looking, I finally took the board out and looked... I forgot to solder 1/2 of an IC. Stoopid.


Reply
Posts: 14
Topic starter
(@ralph-a)
Eminent Member
Joined: 16 years ago

After working on this most of the day, I did the memory wipe thing on the "System Command" button. Then went back and changed them back to the settings for my particular set up. i.e. ws2811 and so forth. YEAH!! It worked. Also Thank you Derek!! IC's all looked good. Checked that earlier today, looking for those stray wires. Can you tell me what the resistor arrays look like and there location? Are they the black things just above the ic's?

Thanks again for all your help. I'm not through all this yet!


Reply
derekbackus
Posts: 565
(@derekbackus)
Honorable Member
Joined: 15 years ago

Well, if you got it working, stop and don't mess with it 🙂

Yes, the resistor arrays are the long, skinny black things (mine were kind of a yellow/brownish/tan color) between the green connectors and the ICs.


Reply
Posts: 14
Topic starter
(@ralph-a)
Eminent Member
Joined: 16 years ago

Got it! Thanks Derek!! Just wanted to know for future reference.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
derekbackus wrote:Well, if you got it working, stop and don't mess with it 🙂

Best advice ever!


Reply
Share: