Emuney18 wrote:What spacing does everyone like for the C9 bulbs? 4,6,8 or 12"
I use 4"
Louie
Sent from my SM-G928V using Tapatalk
nutz4lights wrote:I use Ray Wu's technicolor bulbs. Videos are located at the link below. I am one of those old fashioned nuts that really likes the classical look of a true c9 bulb on the roof. I had the technicolor v1 bulbs that failed. Ray replaced those for me with the technicolor v2 bulbs that failed. I was one of the folks that helped Ray troubleshoot their manufacturing failure. He moved away from injection moulding the base to an epoxy filled setup. Because there wasn't another bulb comparable, i had Ray replace the v2 with the v3 at no cost to me. They have performed perfectly for two years now. 400 bulbs not a single failure.I tested the pixabulb at some point and although it was nice, it is simply not a c9. I suppose if the epoxy filled technicolor bulbs didn't work, i would have considered using the pixabulb, but they DID work and i didn't have to compromise.
Let me know of any questions.
Louie
Sent from my SM-G928V using Tapatalk
Your video information states you have 17,500 WS2811 nodes - if only 400 are Ray Wu's Technicolor, what type are the rest? What has the failure rate been?
I have a mix of bullet style ws2811 pixels and square ws2811 pixels, all from Ray. From memory, there are 2400 + 1600 + 3900 = 7900 square pixels in our megatree, tall palm trees, and window matrix units, respectively. There's 1800 + 2000 + 2000 + 1000 + 1600 =8400 bullet style pixels in our oak tree, twig trees, bushes/short palm trees, wreaths/ornaments, and mini trees, respectively. I'm obviously forgetting something because that only adds up to 16700...
Anyway, some of these lights have gone thru four full seasons without failure. I have personally found that the bullet nodes fail less frequently that the square nodes. I think it has to do with the distance moisture would have to penetrate epoxy fill to get to the circuit board and LED. on the square pixels, that distance is much shorter, and i see higher failure rates with those pixels. Not gonna make me change, though, as those elements sort of require them...
Louie
Sent from my SM-G928V using Tapatalk
Just remembered, we have another 700 bullet pixels in three large wreaths we added last year and another 150 bullet style pixels in our megatree star, pushing the bullet pixel count to 9250 and the total to 17550.
Louie
Sent from my SM-G928V using Tapatalk
Emuney18 wrote:What spacing does everyone like for the C9 bulbs? 4,6,8 or 12"Sent from my iPhone using Tapatalk
12" on the roof and 10" along the ground.
Sent from my iPhone using Tapatalk Pro
Regarding the shape. The pixabulb/brilliant bulb is almost exactly the same diameter as a c9, but its height is only the height of a c7. So they're short and fat.
The strawberry lens shape of the pixabulb makes for a more even light distribution in the lens. The c9 covers in an 8mm mode are much brighter at the base near the led than the end of the bulb. The strawberry bulb is much more evenly distributed comparatively speaking. This really only matters when looking at it from the side. If looking at it top down, they look the same.
Sent from my iPhone using Tapatalk Pro
jchuchla wrote:The strawberry lens shape of the pixabulb makes for a more even light distribution in the lens. The c9 covers in an 8mm mode are much brighter at the base near the led than the end of the bulb. The strawberry bulb is much more evenly distributed comparatively speaking.
I very respectfully disagree. If you look at the picture i posted on the previous page, it seems to me that, yes, the technicolor has a bright short height burst ring at the very bottom, but the color is much more uniform and consistent up the full height of the bulb. The picture shows pixabulb and technicolor in one picture which is a great way to compare apples to apples. The pixabulbs in that picture are all over the place in regards to brightness and color distribution showing far more hot spotting to my eye.
Like you said, though, if you don't aim them up (there is a local guy that aims them at the viewer) you won't be able to tell a difference. I aim mine up. I had that 30 foot section in the video up for several months over the summer and i just had to have the technicolor for bulb height and color uniformity.
Louie
Sent from my SM-G928V using Tapatalk
jpb wrote:For the last 4 Christmas' I have used 2801 5V bullet nodes with C9 covers over them with zero failures. Pictures tell the story but the lights are inside square ducting with holes drilled for a friction fit of the C9 covers. I have them below my gutters as pictured and on the gable ends and ridge.
Can you expand on the square ducting? That is a very clean setup!
I see you've used zip tie mounts under your gutters then zip tied the ducting to the mount. Did you screw in the mounts or are they just stickered?
Love that look. Gives me a few ideas.
What bulb covers did you use? Where did you get them? What size of hole did you drill. I really like your setup ... it's uber water resistant!
Sent from my iPhone using Tapatalk
b0nafide wrote:Can you expand on the square ducting? That is a very clean setup!I see you've used zip tie mounts under your gutters then zip tied the ducting to the mount. Did you screw in the mounts or are they just stickered?
Love that look. Gives me a few ideas.
What bulb covers did you use? Where did you get them? What size of hole did you drill. I really like your setup ... it's uber water resistant!
Sent from my iPhone using Tapatalk
The ducting is 25mm / 1" with spacing between pixels of 45mm. The spacing came about because that is the spacing that comfortably works with strings I had (50mm / 2").
I drilled the holes with a standard twist drill to around 10 to 12mm and then used a tapered reamer to take them to the correct size. Using a 15mm or so drill from the outset was causing too much tear out and resulting in a loose fit but by drilling undersize and then using the reamer it was a more gradual process and gave neater and tighter holes.
I did try to use stick on cable tie mounts under the gutter but in the hot Australian Summer the glue was softening and the cable tie mount falling off. I guess I could have tried a black construction adhesive but I ended up using two long cable ties joined together right around the gutter. I can poke the tie up from the bottom between the gutter and the fascia and then with a bit of a jiggle make it pop out from under the roof tile so I can grab the end. Going the adhesive method I would need to ensure that the one I used would stick to bother the metal gutter and the plastic cable tie mount, and not ooze into the body of the mount and block the holes that the cable tie goes through.
A word of warning, you need to keep the ducting fairly straight while installing it or moving it around because it becomes a bit fragile with the all the holes drilled in it. I get my teenage kids to help put it up and take it down so that the longer lengths are supported in three places.
The pixels I am using look like these but are 2801 and a 50mm spacing
https://www.aliexpress.com/store/product/50pcs-DC5V-12mm-WS2811-led-smart-pixel-node-with-all-color-wire-20AWG-IP68-rated/701799_1932874154.html?spm=2114.12010612.0.0.FdsGnJ
And the covers are also from Ray Wu
https://www.aliexpress.com/item/faceted-White-C9-lens-cover-100pcs-set/32474486311.html?spm=2114.01010208.8.54.STGvzl
The covers are quite heavy and bulky so the shipping cost is a killer. One of the fellas down here is printing his own on a 3D printer and making them cheaper than purchase and shipping costs.
Jon
jpb wrote:For the last 4 Christmas' I have used 2801 5V bullet nodes with C9 covers over them with zero failures. Pictures tell the story but the lights are inside square ducting with holes drilled for a friction fit of the C9 covers. I have them below my gutters as pictured and on the gable ends and ridge.
And then they are stored on the ceiling of the garage in the off season..Jon
Wow - this is exactly what I am looking for. what and where do you find square ducting ? this is a very clean look. can you explain a little more in detail how you attached it below your gutter ?
