RGB strip odd issue
 
Notifications
Clear all

RGB strip odd issue

13 Posts
4 Users
0 Reactions
3,853 Views
Posts: 81
Topic starter
(@djl7780)
Estimable Member
Joined: 16 years ago
[#40145]

Merry Christmas all!
I have a weird issue I was hoping to get some help with. I ordered a few 5m RGB 12v strips from a state side vendor and recieved them yesterday. I connected them to a 6804 (Also connected a few test nodes to verify) and when I turned on any test pattern they light up multi color. I know it's kind of hard to see in the pic, but They should all be red. there is a mixture of red, blue, green and off. Sometimes only half light up etc. No matter what test color I turn on this is what they do. I then moved them to slot 1 same, slot 2, same, slot 3 same. I plugged them into slot 4, the test strings were on 1 and 2, and it made all strings go crazy and blink rapid and odd bluish color..
I did try to adjust voltage down on the PS, but notta...

Any suggestions? Here is the specs from the vendor site:
RGB 5 Meter Strip 150 LEDs 12v White Wire

Size: 15 meters (16.4 feet) long 10mm wide
Chip: WS2811 Smart IC (3 LEDs per IC chip)
Volt: DC 12v
QTY: 150 nodes (30 LEDs per meter)
Waterproofing: IP67 - incased in silicon coating
Wire Color: White
RGB Color: full rgb color, 24bit, 256 gray scale
Max Power Per Pixel: 0.24W (36 Watts total for 5M strip)
Max Current: 120MA

IMG 0507

12 Replies
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

I can't tell from the image, what is the color order that comes up? The first two look like red on the first pixel, blue on the second. Is it a consistent pattern?


Reply
Posts: 81
Topic starter
(@djl7780)
Estimable Member
Joined: 16 years ago

The first pixel is red, then it's a pretty inconsistent pattern after that. I did try changing the order in the controller to a few different combinations with no luck.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

Bummer.


Reply
Posts: 158
(@emmienlightfan)
Estimable Member
Joined: 11 years ago

Hmmm... Strange. Do you have the channels starting at 0? Or some settings still in your controller from other lights?
When you try a different colour or sequence, does the first pixel always light up correctly?


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

re-read your first post Ignore this post.


Reply
Posts: 81
Topic starter
(@djl7780)
Estimable Member
Joined: 16 years ago

I am just running test from the controller itself, not any other software. The bullet nodes turn on as they should..


Reply
Posts: 81
Topic starter
(@djl7780)
Estimable Member
Joined: 16 years ago

Did a bit more troubleshooting and swapped power supplies (both are 30a 12v), same thing. Adjusted the voltage down to about 11.5v and they quit flickering rapidly although the color was blue and it was supposed to be red. Changed the order and it did not respond. Changed the test value to 2 and they did not respond.. Although the bullet nodes did. Unplugged them and they went dark, plugged back up and sent a test. They came on the wrong color, then failed to respond to any other commands..
I'm at a loss, anyone have any ideas?


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

the tests are for rgb and it sounds like your strips arent rgb setup xlights and connect controller and use the test pattern there too find out what the color order is and then set it proper from the sound it might be brg like my friends strips were and I hope you arent plugging them in or unplugging them when controller is powered


Reply
Posts: 81
Topic starter
(@djl7780)
Estimable Member
Joined: 16 years ago

Taz, they are certainly not RGB and are BRG. In xlights if I just select the first 3 channels of this strip it lights for the test in the right colors. If I add say half the strip,75 channels, red lights up, green lights up but flickers, and blue flickers as well. I add the whole strip 150 channels, light up red, and it starts flickering all different colors, same for green and blue.
I have tried injecting power add the end of the strip, I have tried adjusting the output voltage on the PS.

It's hard to believe I was shipped 3 faulty strips? I guess it's possible though. The problem is I do not have another RGB strip to hook up to see if it works..


Reply
Page 1 / 2
Share: