Renard Plus WifiPix...
 
Notifications
Clear all

Renard Plus WifiPixel HELP!?!?

16 Posts
4 Users
0 Reactions
4,913 Views
Posts: 13
Topic starter
(@fuxuepeng)
Active Member
Joined: 9 years ago
[#47160]

I'm new to this and I'm in desperate need of some help from the pros (that's probably you).

I ordered a bunch of wifipixel controllers from the Renard-Plus site. I'm assuming that's the same as the other ESPixelStick designs out there, but considering that it's not working right, I could be wrong. When I power them up on their own I can log into them over wifi, but when they're plugged into the load they won't boot up. I could really use some help troubleshooting the issue.

More details:

  • Affects multiple sticks
  • Tested with multiple strands
  • Wired for 5v WS2811 LEDs. Voltages check out
  • Strands have waterproof 3 pin connectors spliced in. Everything seems to check out
  • ESP8266 flashed with ESPixelStick 3.0. Boots okay without a load
  • With a load both LEDs light up on the ESP8266, but it doesn't boot up

Thank you for any help you can give me

Rex


15 Replies
Posts: 357
Guest
(@jerry72)
Member
Joined: 13 years ago

If you are using Shelbys code, you may need to contact Renard directly, not sure Shelbys is supported on that controller.


Reply
Posts: 355
(@bernard-2)
Honorable Member
Joined: 12 years ago

Concerning Shelby's code, I use it on mine. I flashed a batch load of ESP8266 modules on one ESPstick and move them to other sticks, one of them being a Renard Plus ESPWiFI Pixel Controller.


Reply
Posts: 13
Topic starter
(@fuxuepeng)
Active Member
Joined: 9 years ago
-bernard- wrote:Concerning Shelby's code, I use it on mine. I flashed a batch load of ESP8266 modules on one ESPstick and move them to other sticks, one of them being a Renard Plus ESPWiFI Pixel Controller.

Did you need to do any modifications?


Reply
Posts: 355
(@bernard-2)
Honorable Member
Joined: 12 years ago
fuxuepeng wrote:Did you need to do any modifications?

No, just flashed the module on the ESPstick, remove it from the stick, plugged it to the Renard Plus ESPWIFI board and all good.
Is your module 1mb or 512kb? I think I saw 512 (blue color) won't work but you probably have the 1mb ones (usually black) so that probably is not the issue.
Not sure I understand what you mean by it won't boot up or under load.
Are you connect to the right network?
And how do you power them?


Reply
Posts: 13
Topic starter
(@fuxuepeng)
Active Member
Joined: 9 years ago
-bernard- wrote:No, just flashed the module on the ESPstick, remove it from the stick, plugged it to the Renard Plus ESPWIFI board and all good.
Is your module 1mb or 512kb? I think I saw 512 (blue color) won't work but you probably have the 1mb ones (usually black) so that probably is not the issue.
Not sure I understand what you mean by it won't boot up or under load.
Are you connect to the right network?
And how do you power them?

Probably 1MB, the chips are darker. By boot up I mean that the web server won't load. If the lights are not attached it will sign into the network and I can pull up the web page without a problem. If the lights are attached it won't connect to the network. I'm using a 5v 10amp power supply to power it.


Reply
Posts: 13
Topic starter
(@fuxuepeng)
Active Member
Joined: 9 years ago

What code did you flash it with?


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

Sound like there is an issue w/ the way the lights are wired to the PixelWiFi, double check that you have the +v, Data, and GND connected correctly. Something may be crossed.

Who's pixels? what wire color(s)
Who's Pigtails? What wire colors?

The ESP firmware designed by Shelby will run on and of the different "PixelStick" clones and even the Renard ESP modules (if configured properly for GPIO2).

Shelby's final release for v3.0 can be found here (which is what the OP said he was running.)


Reply
Posts: 13
Topic starter
(@fuxuepeng)
Active Member
Joined: 9 years ago

It's possible.

To check it I measured resistance from the board to the end of the lights for ground and VCC. With the wire with a line on it as ground and the one with text on it as VCC. They came out as expected (around 0 for the same line at with resistance going across).

Here are some pictures:

Sent from my iPhone using Tapatalk


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

You have +V and GND reversed on the pigtail splice to the pixels. Based on the photo of the board, +V is Brown and GND is Blue, which is the proper color scheme. At the splice you have Brown connected to the Right side wire coming from the pixel (GND) and Blue connected the Left side (+V)

pigtail splice1

Reply
Page 1 / 2
Share: