Reliable Pixel Stri...
 
Notifications
Clear all

Reliable Pixel Strips

9 Posts
5 Users
0 Reactions
2,314 Views
Posts: 198
Topic starter
(@thevikester)
Estimable Member
Joined: 14 years ago
[#40263]

I'm looking at changing out my pixel strips within my arches next year, as of each of the last 2 years, I have had failures on every strip. I have 12V 2811's from ray...30 LED per meter, that I had bought 3 years ago...Left half in the packages, and used half the first year...in which there were a number of failures...opened the rest this year, tested...all worked out of the package...and again, within 1 week...failures. They are not in the elements, they are inside the HDPE tubing, so not like they are banged around, exposed to rain, etc..I'm in Florida, and it has been warm, but not that warm : )

So I'm looking for something a little more reliable. Cost is not the issue, hoping someone has had "extraordinary luck" with some model. Prefer 12V,, but can always buy some 5V psu's if need be.

I asked Ray for a recommendation, recommended the same model/crap I already bought, but he said they are more stable now...I have my doubts...I'll still use Ray for most everything, or Paul Z also...as I've been pleased for the most part. So any insight from the lucky ones would be appreciated!


8 Replies
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

I used these on 12 arches this year. Also in 2" HDPE. Got them from Ray earlier this year.
http://www.aliexpress.com/store/product/4m-DC5V-WS2812B-led-pixel-srip-non-waterproof-60pcs-WS2812B-M-with-60pixels-white-PCB-only/701799_935613197.html

All of them worked fine for the whole season except for one that had that cold weather flicker problem that we're all baffled by that goes away when you touch the cable. I tried troubleshooting it for a bit, then just swapped it out. Other people had luck solving this with Ferrite Cores clamps (I didn't - but my clamp didn't quite fit around the cable, so I just cable-tied it).

I cut them down to 142 pixels each, but even so, they definitely need power on both sides. You can't even run red/white alternates without injection.

The 2 years before that, I had these up in 7 arches:
http://www.aliexpress.com/store/product/5m-DC12V-60leds-m-20pcs-ws2811-ic-meter-20pixels-led-digital-strip-IP33-non-waterproof/701799_1192623063.html

They held up kind'a fine for 2 seasons, but I started getting single LED failures here and there in one color, which isn't entirely unexpected. I wanted to switch to 60/60 anyway, so I swapped these for the 5V's above.

I'm happier with the 5V pixels than I was with the 12V ones - it's better for smoother/slower effects.


Reply
jnealand
Posts: 956
(@jnealand)
Prominent Member
Joined: 19 years ago

I gave up on pixel strips for anything. I made my arches out of landscape edging and nodes. Very easy to make and setup. This is the second year for them and they look great.


Reply
DrNeutron
Posts: 2016
(@drneutron)
Noble Member
Joined: 14 years ago

Well going on 3 years with these: http://www.aliexpress.com/store/product/5m-led-digital-strip-DC12V-input-WS2811IC-256-scale-10pcs-IC-and-30pcs-5050-SMD-RGB/701799_568458133.html
Not a single failure and they are out in the elements from Dec 1st until Jan 3rd or so each year....I have a 12 strip Ray tree and they are exposed to some very wild temperature swings and lots of rain/snow/ice. The only issue I have experienced is a bad pigtail and that is my fault when taking down strips (connector froze and I was a little rough with it).
I use Dumb RGB strip for house outline and have had it in PEX for 3 years without a single issue (left up all year). I know people put down Dumb RGB in comparison to pixel, but I'll be darned if it isn't more reliable (no signal issues).


Reply
Posts: 198
Topic starter
(@thevikester)
Estimable Member
Joined: 14 years ago
jnealand wrote:I gave up on pixel strips for anything. I made my arches out of landscape edging and nodes. Very easy to make and setup. This is the second year for them and they look great.

I spent all this money on HDPE tubing...and I'm dang sure gonna use it! If I thought putting nodes inside this tubing would create a decent effect..I would give that a go, but don't think I'd get enough light from it. Perhaps custom 1/2 inch spacing from ray on some square nodes would be the answer...hmmm, that's a thought


Reply
Page 1 / 2
Share: