Question about pixe...
 
Notifications
Clear all

Question about pixel string length, 42 vs. 50

8 Posts
6 Users
0 Reactions
2,460 Views
Posts: 150
Topic starter
(@markl)
Estimable Member
Joined: 19 years ago
[#24917]

As I read about others' pixel tree configurations, I see several that use 42 node strings. At first that made no sense to me, but as I've learned more about pixels I see why that makes sense.

510 effective channels per universe -> 170 pixels -> 4 x 42.5 nodes, so that divides well on the controllers.

2 x 42 nodes x 60ma (typical max power) = 5.04W. I know 5W per connector is what the E682 is designed for. Not sure about other controllers.

So anyway, the number 42 makes some sense. My question to all of you is given that most strings come as 50 nodes, what do you do with the extra 8 pixels? Leave them there as null pixels? Cut them off for later repairs? Something else entirely?

Thanks.
Mark


7 Replies
Lionking_Tx
Posts: 780
(@lionking-tx)
Prominent Member
Joined: 15 years ago

Here my 2c.....

I had a Tree with 42 Pixels per string because of the (at that time) 4 Universe restrictions of the E68x.
Trust me...you can never have enough pixels......

I already upgraded the Network Modules on all E681 I have and will also add 8 Pixels to every string, so it will be 50 Pixels each this year.
I don't have the data sheet in front of me, but the E68x is more than capable of powering 16 strings of 50 pixel (if you use a PS with enough juice).

A 50 Pixel string uses around 3A if set to all white - each output is fused with 5A.
Last year I had a few "fully loaded" controllers (16 strings with 50 pixels each) on my roof and not one failure....OK, a few pixel died, but that's a different issue.

Edit:
Forgot..... Just to clarify
The 42 Pixels were more a "best utilization of the controller" setup at the time when it only supported 4 Universes, but the current Firmware supports 6 Universes on the E682 (or E681 with new Module).
With 6 Universes you can go up to 1530 Pixels per controller which would give you around 95 pixels per connector (but then you look at power injection).


Reply
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago
MarkL wrote:510 effective channels per universe -> 170 pixels -> 4 x 42.5 nodes, so that divides well on the controllers.

2 x 42 nodes x 60ma (typical max power) = 5.04W. I know 5W per connector is what the E682 is designed for. Not sure about other controllers.

So anyway, the number 42 makes some sense. My question to all of you is given that most strings come as 50 nodes, what do you do with the extra 8 pixels? Leave them there as null pixels? Cut them off for later repairs? Something else entirely?

The newer E682 allows strings to span universes/sockets, so you could run longer strings with it (depending on other factors). I think the 42 number was mainly a work-around for the older controller (E680 or maybe E681), as well as being the answer to the ultimate question. 🙂

don


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago

ANd in fact some vendors standard pixel strings are now supplied as 85 on a string.


Reply
Lionking_Tx
Posts: 780
(@lionking-tx)
Prominent Member
Joined: 15 years ago
mrpackethead wrote:ANd in fact some vendors standard pixel strings are now supplied as 85 on a string.

How do they work ? Any power issues (pink pixels) ?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
mrpackethead wrote:ANd in fact some vendors standard pixel strings are now supplied as 85 on a string.

lol - - yeah - - some vendors... I think I can guess one.........


Reply
Posts: 150
Topic starter
(@markl)
Estimable Member
Joined: 19 years ago

Thanks for the responses.

I was hoping to be able to construct a 24 string [half] tree with a single E682. Since the E682 only has 16 connectors, some "strings" will have to be double length. That's where I'm running into the 5A limitation. I might be able to get away with the occasional 6A load without blowing the fuse, but I'd rather not chance it.

24 x 42 also keeps me within the 6 universe limitation the E682 currently has. I know that Jim has new firmware that can increase that to 12, but I haven't seen that made generally available yet. (Although I imagine it will be by Christmas.)

Mark


Reply
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago
MarkL wrote:Thanks for the responses.

I was hoping to be able to construct a 24 string [half] tree with a single E682. Since the E682 only has 16 connectors, some "strings" will have to be double length. That's where I'm running into the 5A limitation. I might be able to get away with the occasional 6A load without blowing the fuse, but I'd rather not chance it.

24 x 42 also keeps me within the 6 universe limitation the E682 currently has. I know that Jim has new firmware that can increase that to 12, but I haven't seen that made generally available yet. (Although I imagine it will be by Christmas.)

Mark

You could replace the stock 5A fuses with 7.5A fuses where you're driving 84 pixels. Average current is so much less than the maximum current that you probably wouldn't pop a 5A fuse.
To run 24 strings I would put doubled strings on 2 of the clusters. Use one cluster on each side of the power supply for doubling to split the load evenly between the 2 power inputs. For the doubled strings, run the first bottom to top as usual, then run the 2nd top to bottom. At the top, connect data and ground (+clock if you use it) together, at the bottom of string 2 connect +V and ground back to the output connector on the E682. Those 2 clusters would be configured as length=84 pixels, zigzag at 42.


Reply
Share: