I have been reading a lot about power injection and I have a couple of questions. When you put the power between the two strings of lights, do you connect the power +/-12v line from the previous string or do you terminate the ends? Second question is where do you put the power supplies, as close as you can get or does that really matter? Thanks in advance.
Sent from my SAMSUNG-SM-N910A using Tapatalk
You can continue the string, but you must ensure the string has sufficient voltage along it entire length.
Where you put the PSUs is all relative to the Cable gauge, Number of pixels, voltage being used.
You will find many discussions on here about this.
Thank you for the response. I am wanting to do some testing when my stuff comes in, but want to make sure I do not damage anything. Is there search suggestion, or just like I have done and just type in power injection. Maybe somebody calls it something different?
Sent from my SAMSUNG-SM-N910A using Tapatalk
in case you did not see this in the wiki http://www.doityourselfchristmas.com/wiki/index.php?title=Power_Injection
lots of good info.
Below is the link to the wiki on power injection that covers fusing and everything else. In short, if you are using the same power supply for both strings and 3 wire pixels, then you connect the V+, V- and Data between the strings. If the strings will be powered by two different power supplies, then only connect the V- and Data between the two strings. Also linked to below is the splitter some use to inject power between two strings using the same power supply. You would have to modify this splitter to cut the V+ line if the strings were going to be powered by two different power supplies. The closer you can place the power supply to the injection point is usually better because then you won't have to worry about or account for voltage drop in the line running from the power supply.
Power Injection Wiki
http://www.doityourselfchristmas.com/wiki/index.php?title=Power_Injection
Power Injection Splitter
http://www.aliexpress.com/store/product/3-core-T-type-waterproof-splitter-the-middle-is-2core-BLACK-color-the-male-connect-s/701799_1707253215.html
This Power Injection here: http://www.doityourselfchristmas.com/googlesearch.html
It is unlikely you will damage anything, as long as you do not over voltage the String.
Be sure you know the string Voltage 5V or 12V.
5V really needs to be between 4.5V and 5.5v Max.
12V with probably work down to 8V, but the colour wont look rigth.
When weird stuff starts happening, like the String locking up, Pixel going all white or only half the string working, its likely to be a Power Issue.
The but test to do, once your pixels arrive, Assuming 12V, Power one end, and using a DVM, measure both ends. 1st with the string off and then 100% White.
Also compare how the string fades as the voltage drops along the length.
I just found the wiki page just before this post. When you say the same power supply, are you referring to the power supply that is connect to the controller? Would that cause you to use all the watts available for the power supply or am I incorrect?
Sent from my SAMSUNG-SM-N910A using Tapatalk
If you are running V+ from the controller to the first pixel in the string, then the same power supply would be the power supply that is powering that pixel output on the controller. It will depend on the the number of pixels on the power supply, size of the power supply and distance of the power injection point as to whether or not you can use that power supply for power injection also. You'll see images of all this outlined in the wiki.
I am not quite sure what you mean.
Depending on the controller you are using, which should have a manual and explain the wiring they recommend.
The wiki shows a number of different methods.
The controller will draw only a few watts of the total power available from the supply.
For for e.g.:- A 12V 25A (300W) PSU in connected to the controller. The controller might use 5W, leaving 295W. However, the controller may only be able to supply a limited current to each string.
If the controller has fused connection to feed the pixel string, fused at 10A. 12Vx10A = 120W, You can you feed 10A from this connection, but if you do not have 120W of pixels connected, you will only use what is connected.
There is nothing stopping you feed the string further down the line, directly from the PSU.
Is this making sense?

