I am trying to run 250 Pixels on each of the 4 ports for a total of 1000 pixels.
I am not sure if the universe numbers are OK or not. Should they be closer together like 182, 184, 186, 190.
I just updated the firmware to the latest version.
I attached two pictures for you to look at.
Thanks for the help
John
On the first page/image you need to set up universe 182, 183, 184, 185, 186, 187 - not just the "starting" universe numbers like you have. Then on the 2nd page/image the ending universe and channel of the first string will be universe 183, channel 240. Then you would start string 2 at either the very next channel (universe 183, channel 241), or you could jump to the next universe (184) and start on channel 1.
The key is, on your first page right now you have gaps in you universes.
I want to have each output start on channel one with a new universe number. All four outputs will have 250 pixels or 750 channels.
The first output starts universe 182 and end on universe 183 channel 240.
I want the second output start on channel 1 universe 184 and end on universe 185 channel 240 and do the same for outputs 3 and 4.
If you look at the 4th output it doesn't have a end universe number.
I have the latest update which lets you use a new universe number for each output.
This is why I don't think it looks right and don't know what to do.
John
Let's start with the input screen. Your controller doesn't know it is supposed to be looking for universes 183, 184, 185, 186, etc. It is only looking for 182, 186, 190, 194. You need to tell it to look for ALL the universes it will use. On the 680x controllers, that is up to 12 different universes in the Unicast mode. (Only 7 universes if you use the multi-cast mode.)
On the outputs page, you would be fine setting it to start on universe 182 - channel 1 which would go to universe 183 - channel 240. (750 channels takes up 510 channels of universe 182, and then 240 channels of universe 183.)
Your second output can start at universe 184 - channel 1. This would take up to universe 185 - channel 240.
Your third output can start at universe 186 - channel 1. It will use all of 186 and a part of 187.
Your fourth output can start at universe 188 - channel 1. It too will use all of 188 and part of 189.
As you have it in your output shot, you are overlapping universes 186, 190, and 194.
Try it, see if I'm right or wrong.
And you don't have to worry about the remainder of the universes you don't use.
Once again, you have to tell the controller what universes to look for in the data stream, not just the starting universes.
algerdes wrote:Let's start with the input screen. Your controller doesn't know it is supposed to be looking for universes 183, 184, 185, 186, etc. It is only looking for 182, 186, 190, 194. You need to tell it to look for ALL the universes it will use. On the 680x controllers, that is up to 12 different universes in the Unicast mode. (Only 7 universes if you use the multi-cast mode.)On the outputs page, you would be fine setting it to start on universe 182 - channel 1 which would go to universe 183 - channel 240. (750 channels takes up 510 channels of universe 182, and then 240 channels of universe 183.)
Your second output can start at universe 184 - channel 1. This would take up to universe 185 - channel 240.
Your third output can start at universe 186 - channel 1. It will use all of 186 and a part of 187.
Your fourth output can start at universe 188 - channel 1. It too will use all of 188 and part of 189.
As you have it in your output shot, you are overlapping universes 186, 190, and 194.
Try it, see if I'm right or wrong.
And you don't have to worry about the remainder of the universes you don't use.
Once again, you have to tell the controller what universes to look for in the data stream, not just the starting universes.
Thank you, Thank you
That was it. I was not putting the universe numbers in sequence in the universe bar.
I new it didn't look right in the output page but didn't know how to fix it.
All is well now, thanks to you and your explanation. I finally got it.
John


