Pixels Flickering -...
 
Notifications
Clear all

Pixels Flickering - Please Help

10 Posts
8 Users
0 Reactions
3,028 Views
Posts: 22
Topic starter
(@johntgonzales)
Trusted Member
Joined: 11 years ago
[#39492]

I have my 5V 2811's that flicker when no signal is being sent and also have like a twinkle when signal is being sent in the green and blue.
Also just my long runs of 12v 2811's are also doing the same. Do I need to power inject or add nulls. Didnt do this when I had short runs and had them set up in the garage.

I have 2 5V power supplies in separate enclosure. Its more of the 5V's than the 12v's. My short runs dont have this problem. Is it a adding nulls issues? Im using 2 E682's and 1 16channel renard.

Check out my videos


9 Replies
Posts: 368
(@henkvis)
Honorable Member
Joined: 18 years ago

Look into all of the other 'flickering' posts...

I solved most of my flickering by using Cat5e cables towards the strings... but still I have a little flickering left....


Reply
Posts: 1344
(@mrsmoofy)
Noble Member
Joined: 12 years ago

Check the voltage of your 5v power supplies make sure they are not turned up to high.


Reply
rfallatt
Posts: 648
(@rfallatt)
Honorable Member
Joined: 16 years ago

I solved my flickering by changing to Cat5e and reducing my intensity to 90% on my F16V2


Reply
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

Make sure your PS grounds are bonded

Sent from my LG-H811 using Tapatalk


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago
rfallatt wrote:I solved my flickering by changing to Cat5e and reducing my intensity to 90% on my F16V2

Backing down the intensity will increase the life too.


Reply
rfallatt
Posts: 648
(@rfallatt)
Honorable Member
Joined: 16 years ago

What do you mean by bonded

Sent from my iPhone using Tapatalk


Reply
Steven010
Posts: 416
(@steven010)
Honorable Member
Joined: 18 years ago

1. Make sure your power supplies share the same 110v voutlet as controller.
2. Pixel data wires are nowhwrre near ac power
3. Any splices in pixels are good (great!).
4. Grounds of pixels, power supplies and controllers are same.
5. Data wire length is raasonable, not too long.
6. Ground wires are not exposed to unintentuonal sources like standing water, metal frames of lights, gutters, etc.
7. power supplies are in range of stated voltages. I.e. 12 v supply is 12v, not 14v. 5v supplly is 5v, not 7v.

Start with this.


Reply
Posts: 22
Topic starter
(@johntgonzales)
Trusted Member
Joined: 11 years ago

Thanks guys, figured it out. My ethernet to my E682's were running next to my lines out from my boxes and creating cross talk on my long wire runs. Glad it was something simple. Thanks for your help, went ahead and dropped my intensity to prolong my pixel life.

My first year doing this. Alot of name calling, head scratching and hair pulling. But these forums with feedback back have help me alot. This is a expensive hobby, but the pay off looking at neighbors and kids faces is what makes it worth it. Got addicted to sequencing songs, its a time warp. Next thing you know its 2 am in the morning and you only got 15 seconds done of a song.

Merry Christmas and thanks guys


Reply
duramadmax
Posts: 904
(@duramadmax)
Noble Member
Joined: 16 years ago

I had bad flickering also on my e682 with some very current firmware. 4.233 I think. Went back to 4.033 and all is well. Plus my units have the pixel pulldown resistor mod.


Reply
Share: