Pixel Controller de...
 
Notifications
Clear all

Pixel Controller decision

26 Posts
15 Users
0 Reactions
10.4 K Views
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
pmiller wrote:I saw talk about USB to serial. Hopefully I can stay within the 50 feet recommended to the first controller. The second controller will be about 85 feet which will work when daisy chained. I understand the E6804 will accept Renard but there are no inputs for serial which leads me to think the Renard can be controlled via one output on the E6804 set to Renard. No extra cable needs to be run. Beats me. I need to look into it more.

Sent from my Nexus 7 using Tapatalk

Yes, an output from the 6804 can drive a Renard or DMX device directly from the output connector. I hesitate to call it RS-485 - more like RS-485-ish in that it supports balanced outputs where the Data line is D+ and the CLOCK line is D- and Ground is - well Ground. You connect the D+/D- to pins 4/5 and Ground to pins 1/2/6 on the Renard and you're good to go. Basically it's similar to simple RS-232 but the other output line (D-) is simply an inverted version of the D+ signal. When flipped/converted by the RS-485 chip on the Renard you end up supporting better noise immunity and therefore longer distances. Not sure specifically for the E6804 but at least a few hundred feet for sure anyway - - definitely a YMMV thing.

On the older E680/E681's as I have (which do not have balanced outputs), I built a small board with an RS485 chip that runs all my Renard stuff out in the yard. It also has an RJ45 connector and Renard/DMX output jumpering so it's very easy to use.


Reply
MartinMueller2003
Posts: 7613
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
mrGrumpy wrote:RS-485 not limited to 50 feet - no max on first device, but I think 4000 feet total run

The max distance for an RS-485 serial connection depends on the quality of the cable, connectors and level conversion devices (chips) at each end.

Cable and connectors:
If you are using CAT5 or CAT6 cable then you are using a good quality cable. Many other twisted pair cables will work as well. Some have better noise rejection characteristics than others so be careful what you buy. This is NOT a good place to save pennies. Make sure you have good solid connections on the ends and your cables are good to go. In my systems, for long runs (100' or more) I use commercial grade CAT6 wire that is used to wire a building. I crimp 'female' connectors onto the ends and then use 12" patch cables at the end to go to the Renard device (This is how I do my Ethernet as well).

USB-To-Serial (RS-485) converter / dongle
Many of us buy the cheapest dongle possible for this. I have not had any issues with the less than $10 dongles going up to 100' using the above cable. A good quality device should be able to give you more than a 1000' run from the converter (dongle) to your first Renard.

Between Renards
The Renards are using a good quality chip set that has a reputation for being a solid performer. Using a good cable you should be able to go greater than 1000' between any Renard devices. I myself have not gone more than 100' between devices so for me 1000' is a theoretical value.

Distance / Delay - The real issue.
In theory, there is no 4000' foot limit in a setup using Renards. For example: You have 10 Ren-8 devices. Each Renard device will regenerate (this is the crucial point) the RS-485 signal. If you had 1000' of cable between each device in your system, you would be using a total 10000' of cable (that is expensive). The real issue becomes propagation delays across the cable (and possible noise injection). Every foot of cable adds a bit of delay and exposure to outside noise. Over 10000' the delay can become noticeable in your display. All is not lost for you long run guys, you can compensate for these delays in your sequence. It is a pain to do, but it can be done. Noise injection is a bit more difficult. RS-485 is designed to reduce the effects of noise injection. However if you drop a loop of communications wire over a motor or the big green transformer in the front of your yard, you may swamp the noise rejection circuit and loose communications. This is not due to cable length and can be a problem on a 6" cable or a 600' cable.

Hope this helps


Reply
smeighan
Posts: 2595
(@smeighan)
Famed Member
Joined: 15 years ago
Bjarmstr wrote: I plan to run my show off Falcon Player as I do not have a dedicated computer for this task. So can this Falcon Beagle run the show, run the lights (if I buy WS2811 / WS2812), and has 8 Dedicated Outputs RJ45 that I read to mean I can run other kinds of light controllers off (if I want something other than the WS2811).
If that is the case (please set me straight where I am wrong), what is the downside? I thought maybe the distance from the controller to the first pixel might be a factor but did I read somewhere that they were stringing the first WS2811 pixel 50' from the controller.
One downside is that they are not out until summer. I did purchase a Komby Sandwich, which I can play with now, but I have pre-ordered more lights than fit on 1 universe. As for the future... who knows how many universes I might want!

The Beagle Bone that drives the Falcon16-B will be a full FPP.
So you can drive 16,32 or 48 strings and it can be your show player also.

Upsides: all that you see in webpage

Downsides:
You may not want all those strings located from one place.
megatree, matrix YES
arches along the side of your yard no.
Only runs one type of lights (tm180x and ws281x). Dave has said he will add more string types later, no commit date on those.

I run 25' from the falcon16 to the first string. it is something like 10-15' or 20-25' depending if you have 2811 nodes or flex strips.

The beta board of the Falcon16-B has been built and tested so it works. The FPP software needs some tweaks and Capt Murdoch asked Dave to set a release date in a few months so he can focus on some other new features he is putting into the FPP code base.

The actual Falcon16-B board has no smd parts, just through assembly. The kit will be easy to assemble as there are not that many parts.

If your lights are tm180x or ws281x then i think the Beagle Bone falcon is the right choice. If you want any type of lights any number of protocols then the falcon16-v2 is better.

if you already have e682, pixlite, p12r controllers and you know those you might want to stay with those.

I have DLA active hubs and falcon16-v1's and no other controllers, so my on-hands experience has only been with those.

I do plan on getting a falcon16-B to add to my yard.

Last year I had three fpp's running. Two of them had video projectors attached. The falcon16-B would just be the 4th fpp added to the group.


Reply
Posts: 114
Topic starter
(@wilkija)
Estimable Member
Joined: 12 years ago

Well I thought I had made the decision to go with the E6804, until I see the thread about a new "6804 nano". If it is priced right, that would be a device that is hard not to purchase.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago
wilkija wrote:Well I thought I had made the decision to go with the E6804, until I see the thread about a new "6804 nano". If it is priced right, that would be a device that is hard not to purchase.

If you're in any kind of a hurry don't wait for the little one. It will be a couple of months, maybe this fall before it's available. And will be harder to mount and wire. So unless ypu need smaller or stand alone the regular 6804 may be a better choice.


Reply
Page 5 / 6
Share: