Pixabulbs injection
 
Notifications
Clear all

Pixabulbs injection

14 Posts
10 Users
0 Reactions
4,754 Views
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago
[#33110]

What are you guys with 12V Pixabulbs doing for injection? Every 50 or 100?


13 Replies
Posts: 191
(@mlevings)
Estimable Member
Joined: 14 years ago

I have 100 pixabulbs without power injection and they look good. The kids just came in and told me I had 3 bulb lot when the rest are off. It rained on them 2 days this week. I hope that's not a sign of what's to come. I have 400 more that are not up yet.


Reply
Posts: 838
(@strother85)
Prominent Member
Joined: 15 years ago
mlevings wrote:I have 100 pixabulbs without power injection and they look good. The kids just came in and told me I had 3 bulb lot when the rest are off. It rained on them 2 days this week. I hope that's not a sign of what's to come. I have 400 more that are not up yet.

I ran my Pixabulbs last year at 100, 100, 100, and 75 long strands off of four e6804 outputs. 10' long 18 gauge waterproof wire/connectors from controller to start of strand. Did not see any pink or flickering at all.

Sent from my SAMSUNG-SM-G900A using Tapatalk 2


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

Looks like every 2 strands...awesome


Reply
corytcline
Posts: 1249
(@corytcline)
Noble Member
Joined: 16 years ago

I have heard of people running 150 off one supply with no injection (3 strands).


Reply
Posts: 528
(@bud29)
Honorable Member
Joined: 17 years ago

I asked Todd Jetzer the same question earlier this year before I bought my pixabulbs, and he suggested 125 pixabulbs would be a safe max per injection point.


Reply
Posts: 7
(@ebecker)
Active Member
Joined: 12 years ago

i am using the sans e6804. If i need to use a second power supply to inject in a run is this possible? if so do i just cut the 12v+ and inejct it or do i inject both 12v+ and - ?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
EBecker wrote:i am using the sans e6804. If i need to use a second power supply to inject in a run is this possible? if so do i just cut the 12v+ and inejct it or do i inject both 12v+ and - ?

You must have a common ground so tie those together and just ensure the two +12v lines do not meet.


Reply
Posts: 972
(@dmoore)
Noble Member
Joined: 17 years ago

Video showing 100 bulbs


Reply
Posts: 384
(@burtonmadness)
Honorable Member
Joined: 14 years ago

Its not just pixels, but if not a continuous run, the drops on connecting wires.

I'm running pixabulbs in my window frames, with 6-14ft 18/2 cable between frames, and had to power injection after about 50pixels (total length abouit 80ft in length). Strange thing, is that I was not getting any pinkness on the final pixels, but in the last frame half way around, I was getting 4-5 pixels flickering just on white. I changed my power injection point closer to the end (rather than middle which I had before) and full white and flickering.

A bit worried about the waterproofing. With El Nino going to hit CA and the several reports and reviews on holidaycoro and here, I'm hoping I'll escape any serious pixel loss. (My windows are not facing west which is the predominant wind direction here. )


Reply
Page 1 / 2
Share: