Nu-bee needs a litt...
 
Notifications
Clear all

Nu-bee needs a little help.

69 Posts
13 Users
0 Reactions
19.1 K Views
Posts: 27
Topic starter
(@tupes)
Eminent Member
Joined: 12 years ago
[#35816]

I'm trying to get my feet wet with rgb without being to complicated at first. What I'm looking at are pixel strips for holiday coro since they're going to be on sale soon. I'm not looking at doing music at this point but will probably add it next year. As far as this year goes I want to get the pixel strips and something like this http://www.holidaycoro.com/DMX-to-SPI-Smart-Pixel-Decoder-Controller-p/614.html but it says it's only for 170 pixels. So unless I did my math wrong it won't work. Is there anything else like it that I can use?

For next year I plan on getting the doohicky that you put the SD card in to play the sequence. I don't have a garage and don't want to leave my laptop outside. Also if you think it's better just to spend the money now and get the whole setup let me know. Also the front of my house is about 60' if I get the pix lite 4 can I just plug in one sting and connect the others end to end.

So if I'm asking so much. I've looked a plenty of videos and websites bit can't seem to find the answers I'm looking for. If you know of a site I can get the answers from please share.

Could someone please give me some advise. Thanks.


68 Replies
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

Here is a list of pixel controllers that will support more than 170 pixels:
http://www.doityourselfchristmas.com/wiki/index.php?title=Controllers

My favorite is the E682 - it supports up to 6020 pixels, and they're $109 if you build it yourself.

But just take that as a start and do more research. There are lots of other factors to consider, such as pixel type, software, power supplies, wiring type & length, location etc.


Reply
Posts: 843
(@captainmurdoch)
Prominent Member
Joined: 14 years ago
tupes wrote:
For next year I plan on getting the doohicky that you put the SD card in to play the sequence. I don't have a garage and don't want to leave my laptop outside.

Take a look at the free Falcon Player which runs on a small Raspberry Pi computer and can control your lights. No need for a full size show PC or laptop. You can put the Pi right outside with one of your controllers and access it over a wired or wireless network connection. All management is done via a web browser. http://FalconChristmas.com


Reply
Posts: 27
Topic starter
(@tupes)
Eminent Member
Joined: 12 years ago

Firstly I want to thank everyone for all the advise they have given so far.

So to give everyone some more information to see what I'm planning I'll make a list of items here.....

-Program: ???????
-Power: http://www.holidaycoro.com/product-p/49-ps.htm
-Computer A.K.A. doohickey: http://www.amazon.com/dp/B00L87YMGM?psc=1
-Controller: http://www.holidaycoro.com/PixLite-4-E1-31-Pixel-Controller-p/622.htm
-Lights 4x: http://www.holidaycoro.com/product-p/700-ps.htm

The main reason I've decided on these items are I'd rather order from one supplier than multiple. If there is anything that I have chosen please let me know.

I think I'm also going to need some 4-22ga wire as said Ill probably need to power inject in the middle. The total length of light will be approximately 55'


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

the px-1 is a simple renard based pixel controller that controls up too 200 pixels per board this was the way i went this year using a couple too control a pixel tree


Reply
Page 1 / 14
Share: