Ok, there is a lot of information out there in regards to pixels. I'm trying to wrap my head around it but I'm more like beating it on the wall trying to figure this out and which way to go. So I would like to get some suggested input from the experts out there. I have 8 arches in my show. They are about 3 feet high and 8 feet long, a total of about 10 feet each. Currently they are made with old in-can lights, about 700 each. I think it's time to upgrade, time to jump in to the pixel pool. I know approximately how much it will cost to convert the arches to LED lights. So I'm looking to get some input on arch costs. Basically;
What to you have?
Pixel type, smart or dumb?
What boards do you use to control them?
What software do you use to control them?
Maybe a estimate of how much you paid for an arch?
I have a rough figure to build 8 dumb arches. Same frame reused with 5050 strips and Ren48LSD boards. I looking at about $600 to produce eight, 8 segment dumb arches. Is going to smart cheaper, less boards, easier? I'm just not sure and not finding the answers. I know it's a busy time of the year for everyone, but once our shows are up and running, this is the time I start planning for the next one.
Thanks in advance for the input.
Mike
What to you have? I use http://www.aliexpress.com/store/product/RGB-full-LED-pixel-module-WS-2801-IC-DC5V-input-50pcs-a-string/701799_521371851.html When I buy more I will probably use these http://www.aliexpress.com/store/product/RGB-full-LED-pixel-module-WS-2811IC-DC5V-input-50pcs-a-string-IP68/701799_563831930.html
Pixel type, smart or dumb? Smart
What boards do you use to control them? http://sandevices.com/E681info.html
What software do you use to control them? LOR S3
Maybe a estimate of how much you paid for an arch? I'm using a full string per arch. The way you have your arches designed, you will get a further distance per string than I did.
Thanks for the input, question, how many stings can be connected to that controller? So if I did one string per arch, how many boards would I need?
One more question, are you diffusing any of them? If so, what are you using.
My arches are made of 1" conduit, I had it rolled to make the arches. I figure to attach the elements directly to the conduit with screws.
mikeh65 wrote:Thanks for the input, question, how many stings can be connected to that controller? So if I did one string per arch, how many boards would I need?One more question, are you diffusing any of them? If so, what are you using.
My arches are made of 1" conduit, I had it rolled to make the arches. I figure to attach the elements directly to the conduit with screws.
16 Strings can be connected. You can also group your pixels and add even more! 1 E682 will be plenty for arches plus a few more elements. I made my arches from 3/4 pvc and used wire ties to attach them. I am not diffusing any of my pixels. You can see what my display looks like in this thread http://doityourselfchristmas.com/forums/showthread.php?23531-2012-Video .
mikeh65 wrote:Thanks for the input, question, how many stings can be connected to that controller? So if I did one string per arch, how many boards would I need? Up to 16 strings per board with a 1020 total pixel limit per board. Note you may have as many or few per string, example 1020 pixel string or 5 strings of 204 or 16 strings of 50. Also note each pixel is three channels red, green, blue.One more question, are you diffusing any of them? No Danny isn't, they come that way. If so, what are you using.
My arches are made of 1" conduit, I had it rolled to make the arches. I figure to attach the elements directly to the conduit with screws.
Several people are using electrical tape or tie wraps to hold them in place. I don't know how you would screw them off hand. I plan to use Nutcracker and Vixen for software and I've started to build mine with GECE 50 ct strings.
Brian
