Hey guys. First time poster. Love the site, very informative. Im looking to o a pixel layout at my house in the coming weeks. Im looking at about 210 linear feet including the dormer up top. Looking for advice on best placement of pixels. Im thinking of mounting them on the outer part of the soffit. Not sure if its best to face them out or face them down. Ive seen mixed opinions. I was initially going to go the j channel route since permatrack is pretty pricey, but stumbled on a product my TBL which is more reasonably priced so I may go that route.
Also some advice on injection points would be great. Im an HVAC contractor by trade so have a strong electrical background so that part of it should be pretty straightforward for me. The back of the house is roughly 30 ft. Each side of the house is 53 ft up to the peak and back down. Front is about 40ft and the dormer is about 25. Going w/ 12v pixels Going to go w/ the Dig Quad controller when it becomes available. Once I get this done, Ill probably add something to my shop in the back of the first photo.
Thanks in advance!
I would try to mount the pixels facing out (horizontal) as close against the building as possible. A few reasons for this: UV Kills pixels. Even a little protection from the eves goes a long way. Water + Heat / cold will also kill your pixels (corrosion from water intrusion via expansion / contraction). When under the eves there is less water (cant do much for hot/cold).
I considered that. Not sure if it would do anything to change the look.
It would still give you the points of light and a nice glow from the eves.
I definitely want it to last. Main reason lm doing it is im tired of putting lights on the roofline every Christmas. Im having the siding but not the soffits painted in the spring but i imagine theyll be enough of a gap to spray behind them. I want to get the lights done now as it is my slower time at work.
Just a side note that has been mentioned many time here on this site, you will still need to consider repairs to your strings when something fails, so make sure you can get access when you need it. While I typically have my roof line lights up for about 6 months of the year (I don't take them down until late April due to snow issues) I have noticed that the lens on the bulbs have faded from UV over time. That said, these strings are going on 10 years and I'm still happy with the colors and the look.
Thanks. The hardest part to access is the sides of the house. The peak runs to the 2nd floor. Its accessible w/ a ladder. For the install, I may rent a boom lift for the day. Would make it go much faster.
One major improvement for me that has made my yearly install/repair of my roof line lights much easier and safer was to make my own C channel and have that installed under my vinyl soffits. I painted my C channel the same color as my soffit, so it really isn't noticeable. I also have a peak on my roof that is about 25' from the ground. By installing permanently mounted C channel under the soffits, it allowed me to place my roof line pixels into a pixel strip and then I can feed it into the C channel at each corner of the house. So I only need to ladder the corner of the house and I have access to two C channels to install my pixels strips. If my I lose a pixel, I can then ladder the corner, disconnect my pixel strip and pull the whole string out without moving my ladder again. Once the repair is complete, I feed the pixel strip back into the C channel. And this works on the longest run on the side of my house which is 44' long.
Aa7483 wrote:Thanks. The hardest part to access is the sides of the house. The peak runs to the 2nd floor. Its accessible w/ a ladder. For the install, I may rent a boom lift for the day. Would make it go much faster.
I dont mount mine. I mounted pullies. Once a year I feed string through the pullies and put my ladder away. After that I raise and lower a PVC pipe with my pixels attached. Allows me to fix things from the ground in cold weather.
Hockeyhunter1956 wrote:One major improvement for me that has made my yearly install/repair of my roof line lights much easier and safer was to make my own C channel and have that installed under my vinyl soffits. I painted my C channel the same color as my soffit, so it really isn't noticeable. I also have a peak on my roof that is about 25' from the ground. By installing permanently mounted C channel under the soffits, it allowed me to place my roof line pixels into a pixel strip and then I can feed it into the C channel at each corner of the house. So I only need to ladder the corner of the house and I have access to two C channels to install my pixels strips. If my I lose a pixel, I can then ladder the corner, disconnect my pixel strip and pull the whole string out without moving my ladder again. Once the repair is complete, I feed the pixel strip back into the C channel. And this works on the longest run on the side of my house which is 44' long.
This sounds like what I need. Can you show some photos of what you have? Also did you mean you feed the strings back in from the top of the peak or can you shove them from below, etc?




