I'm using GECE and I've had 10 failures so far (out of 335). Most are a lost color but a few failures won't pass data. Two of the failures actually fixed themselves with a change of temp outside. All mine are mounted with the bulbs straight up. They're strapped to plastic conduit lining my driveway and gardens. The bases are about 4" off the ground to keep them out of puddles and snow.
--Jon Chuchla--
Sent from my iPhone using Tapatalk
I had one pixel failure all season (Rays 1804 "bullet" style). It did take out the rest of the string, but fortunately was in a place where I could easily splice in a new one.
As I expected some failures, I was quite pleased.
Skunberg wrote:...Or it may work in Calif. but not in New Jersey. .
You got that right.....If I lived in a less humid climate I wouldn't be concerned but here, in the south, this year I experienced heavy fog....and severe thunderstorms with winds upwards of 30MPH..... So the environment isn't friendly to electronics unless you take some extra precautions.... I successfully waterproofed my strobes but I'm not so sure how to go about that with pixels.....but it seems pretty clear to me, after reading various posts, that even IP68 rated ones in an hostile environment will fail..... I can't imagine sitting down to waterproof several thousand pixels.....that sounds somewhat like a fulltime occupation....:w00t:
Well, I linked the guys that had bad luck hoping they would chime in, but I think they wanted to hear from the community first maybe. One had the tsl3001 flat style pixel stapled to his eves. The wire has bad uv damage after just a couple months. So, lesson learned there. The uv damage led to cracking wire that might have helped with the moisture infiltration. But the most moisture damage I see from the pictures happens where the silicone and the led bulb meet. I sent both guys a tube of silicone sealer so they could try to help seal them up. I have no idea what their approach to doing that will be. It would be nice if they could be sealed before the mold is cast during manufacturing but that's unlikely. As was said in an earlier post, we just need to find the best approach to using them knowing they aren't the best at repelling water.
I have a design for strips on my roof that stemmed from several people's ideas I read about here. When I have one finished I'll post it.
Thank you for the replies. And I'm glad to hear that Ray's pixels aren't as bad as we were beginning to think. It just seemed that quite a few locals to this area were having very bad luck with them. I'll see if I can't get some of them to stop by this thread.
Thanks again, and happy new year everyone. Glad to hear of your success.
Jeff
Skunberg wrote:These lights are IP68 when used on a billboard as designed (fronts IP68 backs inside sign). However in our search for the cheapest pixels we take them outside of designed intent which can cause problems. We can deal with those problems or buy different lights designed for our purpose.
In our DIY nature here, we are always looking for more bang for our buck. Sometimes it works great, sometimes needs tweaking, sometimes a flop. Or
it may work in Calif. but not in New Jersey. But that's what this forum is all about. No malice intended just a little food for thought as we all try to work out
what we want to do with this great hobby.
You can not submerse the front half more than 1 meter below water and still have the back half above water for it to be IP68 it has to be fully waterproof I don't care it is designed for signs. For it to have ip68 it has to be fully water proof from all directions. The rating goes on the item itself not something it might get attached to. Here is a little more info on Ingress Protection. http://en.wikipedia.org/wiki/IP_Code
I am using onky GECEs. Out of 396 that were all new this year, i have about 12 bad pixels. All of them pass data, and all of them have some colors that work. I have one string of 36 in particular that has at least 7 bad pixels, and on that string 4 of them are next to each other. Most of the 12 probably 8) were bad right out of the box. Only a few failed during the season. These are on bushes, not oriented in any particular way.
TitusCarnathan wrote: For it to have ip68 it has to be fully water proof from all directions.
I seriously doubt any of these strings have ever been tested by their manufacturers. Remember these are all hand made one at a time. Their IP ratings are more marketing hype. Since the strings do not even include a manufacturer marking, it is hard to really evaluate quality control between manufacturers.
I strongly think that it makes sense to consider additional waterproofing on your $$$$ investment in pixels. Caveat emptor!
I basically figured that they would not test them at the factory.
More than likely I will be getting them form Diy Led Express again. Especially since he got the square pixels in I will give that liquid tape a try.
jklingert wrote:I strongly think that it makes sense to consider additional waterproofing on your $$$$ investment in pixels. Caveat emptor!
Thanks for the link.....had not seen that.....
