Interesting issue
 
Notifications
Clear all

Interesting issue

15 Posts
6 Users
0 Reactions
4,153 Views
Posts: 60
Topic starter
(@demov3)
Trusted Member
Joined: 10 years ago
[#49849]

Second year doing a show and had an interesting problem that did not manifest until tonight. All tested fine every pixel was right.
Well tonight I am running my FM transmitter and the pixels running off the controller nearest to the transmitter are acting way off.

4 beers and half a head of hair later, I learn that the FM transmitter is causing interference on the lines going to the pixels. Push it a few feet away and the problem cleared up instantly.

Hope to help other new folks.
Cheers.


14 Replies
Macrosill
Posts: 9739
(@macrosill)
Member
Joined: 20 years ago

Was it the cables were too close to the antenna or the transmitter itself? How close were they? What kind of cable? What transmitter? How many watts of RF energy are you transmitting? What frequency? What kind of antenna?


Reply
Posts: 60
Topic starter
(@demov3)
Trusted Member
Joined: 10 years ago

Antenna is attached to the transmitter so would say both.
Within a 6 inches to a foot at the closest point.
I am using the holidaycoro.com 3 wire pigtails and extensions.
Transmitter is "Signstek 7W 7C FM Transmitter" from amazon.
It is at the 7 watt limit with the antenna all the way collapsed to fit in a plastic ammo can.
88.5
Little collapsible antenna that came with the transmitter.


Reply
Macrosill
Posts: 9739
(@macrosill)
Member
Joined: 20 years ago

Holy smokes, 7 watts is a lot.

Thanks for the info.


Reply
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago
DemoV3 wrote:Antenna is attached to the transmitter so would say both.
Within a 6 inches to a foot at the closest point.
I am using the holidaycoro.com 3 wire pigtails and extensions.
Transmitter is "Signstek 7W 7C FM Transmitter" from amazon.
It is at the 7 watt limit with the antenna all the way collapsed to fit in a plastic ammo can.
88.5
Little collapsible antenna that came with the transmitter.

Can you reduce the output? I think 1/2 watt is what many use to broadcast in a small area. With 7 watts, you can probably tune in from far away!


Reply
aknflyer
Posts: 371
(@aknflyer)
Reputable Member
Joined: 10 years ago

I see it is adjustable down to 1 watt, which will still exceed FCC limits. At 1 watt you could add a 10db attenuator to get down to 100mw. Plenty far for a display. Something like this: https://www.ebay.com/p/10db-50-ohm-DC-Pass-Inline-Attenuator-Pad-DLS-BNC-3310-Male-female-Connector/1424559548?iid=332461302932
Make sure it is 50 ohm and rated higher than 1watt of power. (if you change to 7watts it will fry this one, as it is only rated to 2watts)
30 yr rf tech.


Reply
Posts: 60
Topic starter
(@demov3)
Trusted Member
Joined: 10 years ago

It claims to be that wattage. I don't trust it as I only get a signal within line of sight of my yard. Or the 4 inch antenna is limiting its range.


Reply
Macrosill
Posts: 9739
(@macrosill)
Member
Joined: 20 years ago

A lot of things can affect your Effective Radiated Power. The short antenna is going to affect your EFP. The transmit power is probably less than advertised as well.

So both would effect you transmit distance.

Thank you for the info regarding how it was installed in relation to the pixel wiring.


Reply
Posts: 60
Topic starter
(@demov3)
Trusted Member
Joined: 10 years ago

Very welcome Brian. 🙂


Reply
JCook
Posts: 1003
(@jcook)
Noble Member
Joined: 13 years ago
DemoV3 wrote:It is at the 7 watt limit

You cannot broadcast with that much power! The FCC will come knocking on your door or slap you with a fine. The EDM transmitter is only 10mw or 100mw and will broadcast 5-6 houses down the street.

Even 1 watt is too much...


Reply
Page 1 / 2
Share: