I am doing somethin...
 
Notifications
Clear all

I am doing something wrong....

5 Posts
3 Users
0 Reactions
1,801 Views
Posts: 368
Topic starter
(@henkvis)
Honorable Member
Joined: 18 years ago
[#39293]

What is my problem: random flickering on 1 string when not receiving data....

Setup: E681-upgraded Unicast

Ouputs:
1 - 2x 20 pixels LPD6803 (12V)
2 - 2x 80 pixels WS2811 (12V) with 'powerinjection' from the end...
3 - 1x 80 pixels + 1x 120 pixels WS2801 (5V)
4 - 2x 80 pixels WS2811 (5V) with 'powerinjection' from the end...

Props:
1 - 2x Megatree stars
2 - 1/2 grid (upper 4 rows of 40pixels)
3 - 5x40 pixel arches
4 - other 1/2 grid (lower 4 rows of 40pixels making a total 8rows of 40pixels)

All pixels are powered direct from my E681, also the 'powerinection' is nothing more than just feeding the power on both end into a string....
Almost all working well, except for 1 of my 12V stings so it seams....

What could cause this? My suspicions is the way i hooked everything up but I cannot figure it out.
So what is 'special' about my setup? I use 4 wire 18AWG to hookup my pixels (30feet away I could use a NULL pixel in between if I have to).
To save on wire, I decided to do the following:
- Red = 12V
- Black = Ground
- Yellow/green = DATA_String 1 (80pixels)
- Blue = DATA_String 2 (80pixels)

connector

I did this for both my 2x80pixels running on 5V and on my 2x80pixels running on 12V.

Now I have only 1 problem and that is random flickering of 1 of my 12V 80pixels strings when no data is sent to it...
Also some noticeable flickering when data is sent, but almost negligible.

Because I can use a NULL pixel in the middle of my 30ft cord, I know that the flickering already is there when I attach only my NULL pixel overthere, meaning in the firs 15ft I already have introduces my problem.

NULL

What is typical: one string is NOT showing this flickering at all whilst the other it is really a problem.
Also, I have setup the 5V pixels the same way, and also there I have no flickering at all...

Also disconnecting on or another pixel string from the controller makes it worse.... looks like an open-loop antenna effect?
I am not seeing it...

Please let me know if you need me to do more diagnostic actions.....
Or if it's not clear from what I describe above, let me know...

Thanks.


4 Replies
rjchu
Posts: 1191
(@rjchu)
Noble Member
Joined: 17 years ago

The whole string of 80 flickers? Then I'd say you have a bad string with a short somewhere or the power injection at the end is shorted to the data line either pulling it up or down depending on if it's Vcc or ground that's shorted to the Dout line. What happens if you replace the string with a different one or disconnect the injection points at the string end?

The only other time I've seen this behavior is when I'm running two data sources at once accidentally meaning HLS and an E1.31 test program are both outputting data at the same time to the same target.

-Joni-


Reply
Posts: 368
Topic starter
(@henkvis)
Honorable Member
Joined: 18 years ago
rjchu wrote:The whole string of 80 flickers? Then I'd say you have a bad string with a short somewhere or the power injection at the end is shorted to the data line either pulling it up or down depending on if it's Vcc or ground that's shorted to the Dout line. What happens if you replace the string with a different one or disconnect the injection points at the string end?

The only other time I've seen this behavior is when I'm running two data sources at once accidentally meaning HLS and an E1.31 test program are both outputting data at the same time to the same target.

-Joni-

Thanks for you remarks.

I forgot to mention that the flickering is quite dim and throughout the whole sting indeed BUT:

1 - I already took away the powerinjection from the end, didn't solve it only took care that the last 20-30 pixels didn't show it anymore probably because it was too faint...
2 - swapping it out with my other 80pix string, so switching the connectors on the E681, transfers the flickering to the other string
3 - Using the "NULL" pixel only on (connected on a 'new' build 15ft wire), the NULL pixel is also flickering... (NOTE: NULL pixel is not set in the controller, so it acts as a 1pixel string).

Based on above findings, I think it has todo something with my connecting wire running from the E681.
A described below, I use the 4 wires to send data to 2 80pxls strings:
- Red = 12V (in common)
- Black = Ground (in common)
- Yellow/green = DATA_String 1 (80pixels)
- Blue = DATA_String 2 (80pixels)

Could this cause my problem?


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

Does e.g. 'DATA_STRING 1' keep flickering if you unplug 'DATA_String 2'?

These aren't balanced wires (like CAT5) - they may not take too kind with another data line running in the same jacket. Even when off, you have output on the data lines - just more 0's than 1's. Introduce a bit of noise and you get flickering.


Reply
rjchu
Posts: 1191
(@rjchu)
Noble Member
Joined: 17 years ago
deonb wrote:Does e.g. 'DATA_STRING 1' keep flickering if you unplug 'DATA_String 2'?

These aren't balanced wires (like CAT5) - they may not take too kind with another data line running in the same jacket. Even when off, you have output on the data lines - just more 0's than 1's. Introduce a bit of noise and you get flickering.

I was going to say the same thing and to try just one of the two data lines to string 2 instead of doubling them up. Perhaps there's a short on one of them or by doubling up the data lines you're picking up even more interference and causing the flickering. I've doubled up power distribution lines but never doubled up data lines.

-Joni-


Reply
Share: