Jeff
I thinking of stringing several 'ends' from a mega tree I built from 50 pixel G35 strings. I only use the first 48 lights. Trouble is how do you mate up the last pixel; no 'exit' leads on my sets. I've got enough to make a 20 pixel string. Has someone worked the problem?
Your thoughts
John
scuba wrote:JeffI thinking of stringing several 'ends' from a mega tree I built from 50 pixel G35 strings. I only use the first 48 lights. Trouble is how do you mate up the last pixel; no 'exit' leads on my sets. I've got enough to make a 20 pixel string. Has someone worked the problem?
Your thoughts
John
Am I glad you made me think about this. I have 16 of the 36 LED sets. I plan on cutting them all down to 32 LED's. I guess I will be cutting out the 4 LED section in the middle and splicing the 2 sections back together. I probably would have cut several before I would have thought about my problem. Thanks!
SO I scarified one end pixel.....It turns out that you only have to connect the center post on the 'last end' of the pixel. you can get the ground and power from splicing the leads in front of the pixel. To get to the center post, you need to mill (not drill) thru the green plastic mold. Use an oversize mill tip, maybe 3/16", and careful mill away the plastic.....There appears to be a small gap between the bottom of the board and the green mold (not confirmed). You may be able to solder a 18g wire to the board to the via...
If I find time next week i'll give it a go... The other option is cut in the middle and remove the required pixels....wish I had thought of that!
John
T'was but a simple process of opening the end pixel and soldering wire to the negative and data to be continued on to the next string. Seal with a bit of J-B weld and close 'er up. These are inserted in a Molex connector. I then cut the 8 channel controller off. Opened it and cleaned up the contacts and removed the wire for the power supply. Then I soldered a 3 lead wire to the board where the string was connected. JB to seal the case and close it up. I have a large number of 6 pin molex connectors so I decided to use them for any DC pixels. I have a standard for 5v, 12v, negative, data and clock. That way there's no mistakes. I solder a pigtail to the positive and negative leads at the beginning of the string, then put Molex pins on all three. Stick them in the connector. I attach the pigtail to the original power supply black wire and heat shrink. Now the string's data and negative can be strung along through all of the strings. Each 8 channel string is powered by it's original wall wart. A little SPT and some vamps... done. The controller pigtail get Molex pins and when plugged into a set of 8 restores them to they way they work out of the box. I didn't like the idea of cutting them off and tossing them. Here are the pics of the end pixel being opened and modded. If there's anything else you care to know about it, let me know now. I've got 6 more sets of 8 cut up, ready to be soldered and modded. As soon as they're done and tested, I'm putting them away until E681 build time... As soon as they're all modded I'll lay them out and test all the different patterns to see how they behave, based on the questions asked. Thank you all for your help, suggestions and the parts. It helps to make this stuff work good.
Jeff
scuba wrote:...There appears to be a small gap between the bottom of the board and the green mold (not confirmed).
John
There is. In fact, it's a small layer of white foam film with a glue backing on it. The green plastic mould isn't adhered to the board around the solder pads. However, there is an SMD resister about 1/8" from the negative pad. It's very easy to get a Dremel bit on that resistor. What I did was carefully grind away material under a large magnifying lamp so I could see the progress. After the first pixel was exposed it was used to help gauge the distances on the others. As soon as I broke through the green plastic to white foam I stopped and then used a tiny razor knive to slice away at the plastic. It's very easy to work with a steady hand. A small jewler's screwdriver and a tiny drill bit gets the foam out of the hole for the wire. I tinned some #22 and soldered it on as it easily fit in the hole. It's enough for the data.
Jeff
