Has anyone experien...
 
Notifications
Clear all

Has anyone experienced this problem?

22 Posts
5 Users
0 Reactions
3,892 Views
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Have you measured the voltage at the end of the string?

SIP only has an effect between the controller and the first pixel in the string. You would be seeing issues at the first pixel if the wire between controller and string was defective.


Reply
Posts: 429
(@mikekrebs)
Reputable Member
Joined: 12 years ago

Post a picture of your genius config. Maybe we will see something in there.

If the same pixel and same brightness every time you cycle the power and it works on the Sans then you most likely have bad firmware or config on the genius.

Does it happen on every port of the genius?

You are saying that both strings on two different ports have exactly the same problem? It is pixel 70 on both strings?

Is the brightness 100% red or something below it?

Did you say the pixel works fine if you send a sequence or test pattern?

If you plug the same cables/props into the Sans Device, all is good?

There is a feature on the Genius board "Repair mode highlights where you need to splice to remove failed pixels*" Is it saying you need to fix me?


Reply
etterm
Posts: 48
Topic starter
(@etterm)
Trusted Member
Joined: 6 years ago

Thank you for all the suggestions. I’ll be trying them all in the next couple of days. The pixels I ordered from Wally’s should be here tomorrow.
I’m going to try my best to post a video and pictures to see if I’m doing something wrong.


Reply
etterm
Posts: 48
Topic starter
(@etterm)
Trusted Member
Joined: 6 years ago

Thank you for all the information. I've included a short video showing that the (1) red pixel is pulsing. Pixels are all WS2811

(1st batch of pixels (1000) for my Mega Tree & 23" Star are from William Lamp Store on AliExpress)
(2nd batch of pixels (500) for 5 X mini trees and stars are from China Light Store on AliExpress)
(3rd batch of pixels (159) for testing are from Wally's Lights (haven't tested these yet)

I changed out the extension cable and it still lights red. I noticed that when I removed postive wire from the extension cable, that runs between both trees, pixel stays lit red but when I remove to negative wire is goes off. Then with positive wire connected and negative wire not connected, pixel is off. I've tripled checked that no wires are crossed and everything is good.

My mini trees are 50 pixels with 20 pixels for stars (cut from a new 50 pixel string) then soldered to end of mini tree pixels.
50 + 20 + 50 + 20 = 140

So, controller powered on , no test pattern running at 50% power.
Voltage at 1st mini tree & star (before extension) is 11.98
Voltage at extension to 2nd mini tree & star is 11.97
Voltage at the solder point between 2nd mini tree & star is 11.94

With controller at 50% power and pixel marker test pattern on.
Voltage at 1st mini tree & star (before extension) is 9.64
Voltage at extension to 2nd mini tree & star is 9.51
Voltage at the solder point between 2nd mini tree & star is 8.85

I added power injection and tested same voltage points as above and the voltage didn't go below 11.30

Red pixel stayed on through all tests.

It happens on all 16 ports.

pixel trees
settings

Reply
etterm
Posts: 48
Topic starter
(@etterm)
Trusted Member
Joined: 6 years ago
MikeKrebs wrote:Post a picture of your genius config. Maybe we will see something in there.

If the same pixel and same brightness every time you cycle the power and it works on the Sans then you most likely have bad firmware or config on the genius.

Does it happen on every port of the genius?

You are saying that both strings on two different ports have exactly the same problem? It is pixel 70 on both strings?

Is the brightness 100% red or something below it?

Did you say the pixel works fine if you send a sequence or test pattern?

If you plug the same cables/props into the Sans Device, all is good?

There is a feature on the Genius board "Repair mode highlights where you need to splice to remove failed pixels*" Is it saying you need to fix me?

Yes, it happens on every port of Genius.
I have 50 pixels then 20 soldered to mini tree - extension cable - 50 pixels then 20 pixels soldered to mini tree. 140 pixels on 1 port.
I've tested at 50,60,70,80,90 & 100 percent, stays red and it pulses.
On test pattern it acts more normal but I noticed the red is on as well.
I've sold the E682's , can't test on SanDevices.

Can you help me with the "repair mode" feature? Where is it located?

Thank you for your time.


Reply
Page 2 / 5
Share: