Finally got em fini...
 
Notifications
Clear all

Finally got em finished.

162 Posts
38 Users
0 Reactions
54.4 K Views
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 19 years ago

WS2812B is a 5V chip.

Craig, As I get more and more of them connected I can see that the voltage drop is going to be a problem. I need to see how 12V works for the distance covered before I start looking for a power supply. But I might choose to go with 24 after all. Were your DC to DC converters waterproof and where'd you get them?

I find that with the equivalent of 750 pixels connected, the voltage drop 22' from the power supply is 3.3 volts. I tried turning up the supply but it was already maxed out at only 4.6 volts. Good thing I tested. Tried another supply with the same results. I can see a color shift in several places. I'm going to try adding another 5 volt supply before going to the expense of more DC to DC converters but I'm not optimistic. ...snip...

EDIT: I switched everything back over to the 12/5v 15W Buck convertors. I only have 7 of them on hand so I did what I could but I'm getting 5 volts at every 6th Icicle break. So I have a plan, and I ordered a dozen more bucks from eBay. (...and the pixels are all bright white now!)

Jeff


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

Every 6th icicle break. Does that come out to about 2 meters of strip off the reel?


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 19 years ago

Yep. 30 pixels per 3 icicle set. 30 per meter.

Jeff


Reply
Posts: 2229
Topic starter
(@plasmadrive)
Famed Member
Joined: 15 years ago
Jeff Millard wrote:WS2812B is a 5V chip.

Craig, As I get more and more of them connected I can see that the voltage drop is going to be a problem. I need to see how 12V works for the distance covered before I start looking for a power supply. But I might choose to go with 24 after all. Were your DC to DC converters waterproof and where'd you get them?

I find that with the equivalent of 750 pixels connected, the voltage drop 22' from the power supply is 3.3 volts. I tried turning up the supply but it was already maxed out at only 4.6 volts. Good thing I tested. Tried another supply with the same results. I can see a color shift in several places. I'm going to try adding another 5 volt supply before going to the expense of more DC to DC converters but I'm not optimistic. ...snip...

EDIT: I switched everything back over to the 12/5v 15W Buck convertors. I only have 7 of them on hand so I did what I could but I'm getting 5 volts at every 6th Icicle break. So I have a plan, and I ordered a dozen more bucks from eBay. (...and the pixels are all bright white now!)

Jeff

Hey Jeff,

You are going thru what I did in the beginning. That is why I went with converters.. and why I center fed every set of 6 Icicles. That means that my converters are feeding 2 meters worth but from the center so no more than 1m per run.

The reason I used 24vdc supplies is two fold. First, I had lots of them. (I still have about 60 of em). Secondly I could use a single set of #14 wires to feed the entire distance. Vdrop was not an issue for me at all.

Craig


Reply
Posts: 33
(@travis)
Eminent Member
Joined: 19 years ago

Craig,
Where can I find the converters ?


Reply
Posts: 2229
Topic starter
(@plasmadrive)
Famed Member
Joined: 15 years ago

Travis,

There are many dealers for DC-DC converters. Ebay, Ray Wu, I think some of the local dealer have some. I have about 40-50 I can sell, but they are not waterproof. Mine are supposed to be 3 amp type but that may be pushing them a bit, not sure. I bought 5 amp units for the Plasma Icicles and used them all, but I would not recommend the company so I don't name them.

Craig


Reply
Posts: 556
 jpb
(@jpb)
Honorable Member
Joined: 19 years ago
Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 19 years ago

Here's a 12v to 5v DC to DC convertor from eBay. I have 10 of these in props that are out in the rain today. They work great for the Plasma Icicles all paralleled up on both the source and load side. I like them so much I put in another order for 14 more of them.

Now, what to do with the 3 5V 450 watt power supplies I have on hand?!?

Here's another version I use.

Jeff


Reply
Posts: 2229
Topic starter
(@plasmadrive)
Famed Member
Joined: 15 years ago
Jeff Millard wrote:Here's a 12v to 5v DC to DC convertor from eBay. I have 10 of these in props that are out in the rain today. They work great for the Plasma Icicles all paralleled up on both the source and load side. I like them so much I put in another order for 14 more of them.

Now, what to do with the 3 5V 450 watt power supplies I have on hand?!?

Here's another version I use.

Jeff

Put them at the base of your new pixel mega tree.. you know.. the one you now have to build! LOL


Reply
Posts: 33
(@travis)
Eminent Member
Joined: 19 years ago

Thank you.
I love the look of these lights.
I have a gutter line of 42 ft. that I want to put them on.
Can't wait to get my hands on some.


Reply
Page 7 / 17
Share: